![. DC POWER SUPPLY:](/images/new-backgrounds/160016/1600169x1.webp)
. DC POWER SUPPLY:
1.Be sure the DC power supply is 12V- 14V, attach the plug of DC power cord to the DC socket on the back of the cabinet. The set will be in stand by mode, the power indicator is red.
If this television is being used in a mobile installation, attach the small connector of the supplied Car Battery Cord to the DC 12V jack on the rear of the
set, and the power indicator lighted.
2.3same as AC POWER SUPPLY.
ATTENTION :
1.Unplug the power cord when you are not watching the set:
2.Be sure the polarity of the power supply is correct when operating on DC power supply.
3.Be sure the tolerance current of the DC power supply cord( not supplied) is over 5A. If not, it will be very hot and very dangerous for you safety.
.
.
CHANNEL SELECTION
This set is preset to Australia channels 2,7,9,10,28 on those numbers. If you wish to change the settings, or add more channels, the method is quite straight forward.
Press CHANNEL SELECTOR button on the appliance or the Remote Control Unit, the channel number will be increased or decrease as shown in the following Fig, and displayed in the upper right comer of the screen.
|
|
|
|
|
|
|
|
| CHANNEL INCREASE |
|
|
| ||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
| |||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
CH |
|
| 0 |
|
| 1 |
|
| 8 |
|
| 58 |
|
| 59 |
|
|
| CH | CH | ||||||
|
|
|
|
|
|
|
|
|
|
|
| |||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
| CHANNEL DECREASE |
|
|
|
|
|
|
|
|
| ||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||||||||
(REMOTE) |
|
| 0 |
|
| 1 |
|
| 8 |
|
| 58 |
|
| 59 |
|
| (THE APPLIANCE) | ||||||||
|
|
|
|
|
|
|
| |||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
. Use the CHANNEL SELECTOR button on the Remote Control Unit to select channel.
a)Single digit channel
In this method, you can only select any one of
b)
In this method, you should press the
NOTE: To select
* PREVIOUS BUTTON (REMOTE CONTROL UNIT)
Pressing this button to select the channel that was tuned immediately before the one being watched. For example: If you are watching the program on channel 6, and the previous program you watched is on channel 15; then you can press the button to reach channel 15, press it again to return channel 6.
4