MAX 5300-PMBACK PANEL FEATURES, MAX 5300-PMSPECIFICATIONS

MAX® 5300-PM BACK PANEL FEATURES

1. 15A Main Circuit	2. Outlet Bank 5	3. Outlet Banks 3 and 4
Breaker:	Two switched, high-current outlets controlled by	Each bank features two switched outlets with linear
Automatically opens	the front panel Power Button or the DC Trigger in-	filtration technology (LiFT) controlled by the front
when the current load	put. Bank 5 has a 5 second turn on delay and turns	panel Power Button or the DC Trigger input. Banks
is greater than 15	off immediately upon shutdown. The High Current	3 & 4 will turn on immediately and turn off after a
Amps. Push to reset.	outlets provide power from a low impedance noise	10 second delay. LiFT EMI/RFI noise filtration is
	filtration circuit that does not limit the current to	provided by a two-stage balanced Pi filter which
	your equipment. Its output is noise-isolated from all	also provides noise isolation from all other outlet
	other outlet banks.	banks.

4. Outlet Banks 1 and 2

Each bank features two always-on outlets with linear filtration technology (LiFT). Power will only be turned off under a fault condition. (See specifications for over-voltage and under-voltage thresholds). LiFT EMI/RFI noise filtration is provided by a two-stage balanced Pi filter which also provides noise isolation from all other outlet banks.

5.Universal TV Coaxial Jacks

3pairs of bidirectional protection circuits optimized for satellite, cable, and antenna TV signal lines.

6. Main Power Cord 10ft.	7. Ground Lug:	8. Bank 1 & 2 Indicator
Must be plugged into a	Provides a common	Light
properly wired & grounded	grounding point for	Normally ON, is lit when
3-wire outlet.	equipment with separate	there is power present
	ground leads.	on the Bank 1 and 2
		receptacles.

MAX® 5300-PM SPECIFICATIONS

9.Voltage Sense Trigger Output

3.5mm (1/8”) Mini-Plug jack. Connecting a trigger wire to the Voltage Sense Output jack will allow the input signal to pass through the M5300-PM to control the startup/shutdown of an additional device.

10.Voltage Sense Trigger Input

3.5mm (1/8”) mono mini-plug. Connect to a remote trigger device that uses a DC output to trigger a startup/shutdown sequence.

11. LAN Jacks

Protection circuits for 10/100 baseT Ethernet lines. For the LAN 2 protected jacks, the incom- ing LAN line MUST be plugged into the LINE jack and the patch cord to the equipment MUST be plugged into the EQUIP jack. For the LAN 1 protected jacks the incoming LAN line must be plugged into the LINE jack and the equipment must be plugged into the gaming jack on the front panel. 8 wire protection, 52V clamping.

12. Phone Jacks

Protection circuits for standard telephone or pay-per-view lines. Phone circuit is autoresetting. Incoming phone cord MUST be plugged into the LINE jack. Patch cords to the equipment (satellite receiver, digital video recorder, telephone, etc.) MUST be plugged into the EQUIP jacks.

General________________________________________________________________

Dimensions	17 in. W x 12.75 in. D x 3.5 in H, (4.1 in. Including feet)
Weight	30 lbs.
AC Power_______________________________________________________________
Line Voltage	120V, 60Hz
Total Current Capacity	15 A
UL1449 Suppression Rating	330V
Protection Modes	L-N, L-G, N-G
Initial Clamping Level	200V
Energy Dissipation	2125 Joules
Peak Impulse Current	72,000 Amps
Catastrophic Surge Circuit	Yes
Thermal Fusing	Yes
Over-voltage shutoff	142 VAC ± 8 VAC
Under-voltage shutoff	90 VAC ± 2 VAC
EMI/RFI Noise Filtration___________________________________________________
Banks 1, 2, 3, 4	80 db, 100 KHz – 2 MHz
Bank 5, High Current Outlets	60 db, 100 KHz – 2 MHz
DC Trigger Input__________________________________________________________
Jacks	3.5mm (1/8”) mono mini-plug
Voltage and Polarity	3 - 24V DC, bidirectional
Current Requirement	4.6 mA @3V, 58 mA @24V
DC Trigger Output________________________________________________________
Pass through	no delay
Positive = Tip, Negative = Ring

LAN Circuits_____________________________________________________________

Clamping Level	52V
Connectors	RJ-45
Wires Protected:	8-Wires
USB Circuit_____________________________________________________________
Jacks	USB-A
Power Delivery	500 mA @ 5 VDC
Telco Circuit____________________________________________________________
Fuseless/Auto-resetting	Yes
Clamping Level	260V
Capacitance	30pf (approx.)
Suppression Modes	Metallic & Longitudinal
Wires Protected	2-Wire, Pins 4 & 5
Connectors	RJ-11
Cable and Satellite Circuits________________________________________________
HD 1080 i/p Ready	Yes
Shielded	Yes
Clamping Level	75V
Frequency Range	0 MHz - 2.2 GHz
Insertion Loss	< 0.5 dB
Connections	Female “F”, Gold Plated
Bidirectional	Yes

Design and specifications subject to change without notice due to product improvement.

UPC’S, QUANTITIES, WEIGHTS & MEASUREMENTS FOR ORDERING & SHIPPING

MODEL M5300-PM

UNIT CARTON

MASTER CARTON

17” x 12.75” x 3.5”

30 lbs

23.75” x 18.5” x 10”

33.5 Lbs

0 50616 00816 7

Same as

33.5 Lbs

4.1” H with feet

Unit Carton

5 00 50616 00816 2

1690 Corporate Circle, Petaluma, CA. 94954 800-472-5555 or 707-283-5900 Fax 707-283-5901 www.panamax.com

Panamax MAX 5300-PMBACK PANEL FEATURES, MAX 5300-PMSPECIFICATIONS, MODEL M5300-PM, Same as

Models: MAX 5300-PM