Panasonic CQ-JV1060L dimensions Terminals Description

V.W. / CQ-JV1060L

7 TERMINALS DESCRIPTION

7.1.Main Block

IC701 : C2CBKA00001

Pin	Port	Descriptions	I/O	Vol.
No.				(V)
1	RSTOUT	Not used	-	-
2	NMI	(VDD pull-up)	-	4.8
3	VSS	Ground	-	0
4	VDD	+5V power supply	-	4.8
5	LCD.ADR	LCD addrress	O	0
6	CD.SW3	CD disc out	I	4.4
7	CD.SW1	CD disc in	I	4.5
8	P.ON	System power on	O	4.8
9	CAN6.1V	Battery level detection (6.1V)	I	4.7
10	SAFE	Safety LED control	O	4.8
11	ILL2	Illumi. on (LCD)	O	4.8
12	ILL	Illumi. on (Button)	O	4.8
13	KI0	Key data input	I	0
14	KI1	Key data input	I	0
15	KI2	Key data input	I	0
16	KI3	Key data input	I	0
17	VSS	Ground	-	0
18	VDD	+5V power supply	-	4.8
19	SR.DATA	Serial data	I/O	4.8
20	SR.CLK	Clock for serial data	O	4.8
21	ANT.CNT	ANT1 amp power control	O	0
22	A/B.IN	Tape side detection	I	4.7
23	TUN.A	Tuning/Scan SW	I	0
24	TUN.B	Tuning/Scan SW	I	0
25	VSS	Ground	-	0
26	VDD	+5V power supply	-	4.8
27	DEV	FM deviation	I	0
28	ADJ	FM adjacent interference	I	0
29	M.P	FM multipath interference	I	0
30	FILD	Fieldstrength level	I	0.5
31	IF.V	ANT2 current intensity	I	0.5
32	ANT.V	ANT1 current intensity	I	0.5
33	BATT.V	Battery level detection	I	2.6
34	FAD	Fader level	I	2.3
35	VA.REF	+5V power supply	-	4.8
36	VA.GND	Ground	-	0
37	BAL	Balance level	I	2.3
38	TRE	Treble level	I	0
39	MID	Middle level	I	1.0
40	BASS	Bass level	I	1.0
41	VSS	Ground	-	0
42	VDD	+5V power supply	-	4.8
43	BAT.DET	Battery level detection	I	4.8
44	CC.EJ	Tape eject	I	4.8
45	CD.EJ	CD eject	I	1.8
46	ALARM	Alarm signal	I	0
47	P.SW	Power on SW	I	4.8
48	CD.SW2	CD SW2 input	I	0
49	T.LOAD	Tape loading detection	I	0
50	DIAG.CONT	Not used	-	-
51	VSS	Ground	-	0
52	VDD	+5V power supply	-	4.8
53	IF.ON	ANT2 amp power control	O	0
54	RADIO.ON	Radio power control	O	4.8
55	DSP.DET	DSP in activity	I	4.8
56	CD.RST	CD reset	O	4.8
57	CD.SIM0	CD serial data	O	0
58	CD.ON	CD controller enable	O	0
59	BIT3	Tape mode SW	I	0
60	BIT2	Tape mode SW	I	0
61	CDC.REMO	CD.CH remocon data	O	0
62	CDC.DATA	CD.CH data	I	0
63	BIT1	Tape mode SW	I	0
64	EQ	Metal tape detection	I
65	MS	MS detection	I	0
66	CDC.CLK	Shift clock for CD.CH data	O	0
67	LCD.DET	LCD driver in activity	I	0

Pin	Port		Descriptions	I/O	Vol.
No.					(V)
68	VDD	+5V	power supply	-	4.8
69	VSS	Ground		-	0
70	CD.SOMI	CD serial data		I	0
71	/T.MUT	Telephon mute		I	0
72	CD.SCKM	Shift clock for CD data		O	0
73	CAN.EN	CAN BUS enable		O	0
74	CAN.STB	CAN BUS strobe		O	0
75	CAN.RX	CAN BUS data		I	4.8
76	CAN.TX	CAN BUS data		O	4.8
77	CAN.N.ERR	CAN BUS error		I	4.8
78	VDD	+5V power supply		-	4.8
79	VSS	Ground		-	0
80	/RD	Not used		-	-
81	/WR	Not used		-	-
82	/READY	Not used		-	-
83	ALE	Not used		-	-
84	/EA	(VDD pull-up)		-	0
85	K00	Key scan		O	1.2
86	K01	Key scan		O	1.2
87	K02	Key scan		O	0
88	K03	Key scan		O	1.2
89	PL04	Not used		-	-
90	R.IN	Tape reverse		O	0
91	T.IN	Tape-in detection		I	0
92	ENDA	Tape end detection		I	0
93	VDD	+5V power supply		-	4.8
94	VSS	Ground		-	0
95	CD.ON10V	CD power on (10V)		O	4.6
96	M2F	Main motor control		O	4.8
97	CC.ON	Tape power on		O	0
98	ENDB	Tape end detection		I	0
99	GAIN	Audio output level control		O	4.8
100	CD.ON5V	CD power on (5V)		O	4.8
101	F.IN	Tape forword		O	0
102	LCD.ON	LCD driver reset		O	4.8
103	E2DATA	Security data		I	0
104	ST-BY	Power amp stand-by		O	4.8
105	DSP.RST	DSP reset		O	4.8
106	AMP.ON	External AMP power on		O	0
107	MUT	Not used		-	4.8
108	M2	Main motor control		O	0
109	VOL.A	Volume control signal		I	0
110	VOL.B	Volume control signal		I	0
111	VDD	+5V power supply		-	4.8
112	VSS	Ground		-	0
113	E2CE	Security ROM chip enable		O	0
114	LCD/E2 DT	LCD/Security data		O	0
115	LCD/E2 CK	Clock for LCD/Security data		O	0
116	LCD CS2	LCD driver select		O	0
117	F/E.STP	Radio stopsignal input		I	0.9
118	F/E.DATA	Tuner control data		O	0
119	F/E.ENA	Tuner enable		O	0
120	F/E.CLK	Shift clock for control data		O	0
121	VDD	+5V power supply		-	4.8
122	VSS	Ground		-	0
123	XTAL2	Crystal oscillator		-	2.0
124	XTAL1	Crystal osdillator		-	2.3
125	VSS	Ground		-	0
126	XTAL3	Crystal oscillator		-	2.3
127	XTAL4	Crystal oscillator		-	2.3
128	RST	Reset		I	4.9

Note 1 : Voltage measuerments are with respect to ground,

with a voltmeter (internal resistance : 10M ohms).

8