oping, and maintain the cutting per- formance.
With the system outer foil in place, apply some hand soap onto the outer foil.
Push and hold the On/Off switch for more than 2 seconds to activate the turbo mode for “sonic” vibration cleaning.
At the same time, the “sonic” clean- ing symbol appears in the LCD dis- play (ES8164), or the lamps of the Battery capacity monitor (ES8162) illuminate randomly.
Pour some water over the outer foil. After about 20 seconds, it will be automatically turned off, or you can turn it off by pushing the On/Off switch.
Remove the system for foil and push the On/Off switch more than 2 seconds to activate the turbo mode for “sonic” vibration cleaning and clean it with running water.
Wipe off any moisture from the shaver with a dry cloth and dry it with- out the system outer foil.
It is recommended to clean your shaver with the “sonic” vibration cleaning when the tap symbol (a) appears in LCD (ES8164).
Replacing shaving head components
Replacing the system outer foil (see fig. 8)
Squeeze the system outer foil re- lease buttons and lift the system outer foil upward to remove it. To in- sert the new system outer foil, press down until it snaps into place.
Replacing the inner blades (see fig. 9)
Squeeze the system outer foil release buttons and lift the system outer foil upward to remove it. Remove the in- ner blade one at a time by grasping each firmly at both ends and pulling straight away from the shaver.
Do not touch the metal parts of inner blades.
To insert the new inner blade, hold the blade one at a time at both ends and press downward until each snaps into the shaver.
ATTENTION:
A
How to remove the
(see fig. 10)
WARNING:
Do not attempt to replace the bat- tery for the purpose of reusing the shaver. This could result in the risk of fire or electric shock.
The battery in this shaver is not in- tended to be replaced by consum- ers. However, the battery may be re- placed at an authorized service center. The procedure described be- low is intended only for removal of the rechargeable battery for the pur- pose of proper disposal.
1.Disconnect the power cord from the shaver when removing the battery.
2.Remove the bottom cover screw
(a).
3.Remove the bottom cover (b).
4.Slide the back panel (c) and re- move it.
5.Remove the housing clip (d).
6.Remove the four housing screws
(e).
7.Remove the housing B (f).
8.Lift the battery (g) and remove it.
Caution – To prevent personal injury or damage
ES8162 shaver.
• Dry the shaver completely before |
charging it. |
• The shaver and adaptor will be- |
come slightly hot during use or |
charging, however, this is not a |
malfunction. |
• Keep the adaptor away from water |
and handle it only with dry hands. |
• Grip the adaptor when disconnect- |
ing it from an AC outlet; tugging on |
the power cord may damage it. |
• Store the adaptor in a dry area |
where it will be protected from dam- |
age. |
• Do not pull, twist, or severely bend |
the power cord. |
• Do not wrap the power cord tightly |
around the appliance. |
• If the power cord gets damaged, it |
alone can not be replaced. |
Contact an authorized service |
center. |
• In cases where static noise is emit- |
ted from the television during use |
or recharging, connect the adap- |
tor to a different outlet. |
• Do not touch the edge (metal part) |
of the inner blade. |
Failure to observe this may lead to |
hand injuries. |
• Wash the shaver in tap water. Do |
not use salt water or boiling water. |
Also, do not use cleaning products |
that are designed for toilets, bath- |
It is recommended that you replace the system outer foil at least once a year and the inner blade at least once every 2 years to maintain your shav- er’s cutting performance.
10
9
WARNING for Lithium Battery: Fire, explosion, and severe burn hazard.
Do not crush, disassemble, heat above 100°C (212°F), or inciner- ate.
to the product,
•Do not charge the shaver where it will be exposed to direct sunlight or a heat source, or where there is a lot of moisture.
•Use only the included adaptor
11
10
rooms or kitchen appliances. Do |
not submerge the shaver for a long |
time. |
• Do not wipe any part of the shaver |
with thinner, benzine or alcohol. |
Clean it by using a cloth dampened |
with soapy water. |
