S P E C F I L E
LCD Projector
PT-F300NT
Control commands
Command: <Parameter> | Function | Callback: <Parameter> | Parameter value | ||
|
|
|
| Min | Max |
|
|
|
|
|
|
PON *1 |
| Power on (standby mode on) | PON | – | – |
POF *1 |
| Power off (standby mode off) | POF | – | – |
AVL:<pl> | Volume control | AVL:<pl> | 0 | 63 | |
IIS:<input signal> | Input signal selection | IIS:<input signal> | – | – | |
OST |
| The same function as “default” button | OST | – | – |
OFZ:<off on> | Freeze | OFZ:<off_on> | 0 | 1 | |
OEN |
| Enter | OEN | – | – |
OXG: | 0 | Wide mode: Off | OXG:0 | – | – |
OXG: | 1 | Wide mode: On | OXG:1 | – | – |
OXG: | 2 | Wide mode: Auto | OXG:2 | – | – |
VPM:<NAT> | Picture mode: Natural | VPM:<NAT> | – | – | |
VPM:<STD> | Picture mode: Standard | VPM:<STD> | – | – | |
VPM:<CIN> | Picture mode: Cinema | VPM:<CIN> | – | – | |
VPM:<DYN> | Picture mode: Dynamic | VPM:<DYN> | – | – | |
VPM:<BBD> | Picture mode: Blackboard | VPM:<BBD> | – | – | |
VXX:DLVI0=<+00000> | Daylight View: Off | VXX:DLVI0=<+00000> | – | – | |
VXX:DLVI0=<+00001> | Daylight View: Auto | VXX:DLVI0=<+00001> | – | – | |
VXX:DLVI0=<+00002> | Daylight View: On | VXX:DLVI0=<+00002> | – | – | |
AUU |
| Volume up | AUU | – | |
AUD |
| Volume down | AUD | – | – |
OMN |
| Menu | OMN | – | – |
OCU |
| Cursor up | OCU | – | – |
OCD |
| Cursor down | OCD | – | – |
OCL |
| Cursor left | OCL | – | – |
OCR |
| Cursor right | OCR | – | – |
OAS |
| Auto setup | OAS | – | – |
OSH *1/*2 |
| Shutter | OSH | – | – |
OIX |
| Index window | OIX | – | – |
DZU |
| Digital zoom: Enlargement | DZU | – | – |
DZD |
| Digital zoom: Reduction | DZD | – | – |
TSD:<date> | Date setting | TSD:<date> | – | – | |
TST:<time> | Time setting | TST:<time> | – | – | |
*1 Do not send PON, POF, or OSH commands continuously in a short period of time. Doing so may burst the lamp or shorten the lamp replacement cycle.
*2 When a command other than OSH is sent while the shutter function is operating, the projector will send an ER401 command in reply and release the shutter function.
Status asking commands
Command | Description |
| Callback |
|
|
|
| <Parameter> | |
|
|
|
|
|
QPW | Standby power status |
| <power | condition> |
Q$S | Lamp status |
| <lamp | condition> |
QIN | Input signal status |
| <input | signal> |
QAV | Volume adjustment value | <pl> |
| |
QVC | Color adjustment value |
| <pl> |
|
QVT | Tint adjustent value |
| <pl> |
|
QVB | Brightness adjustment value | <pl> |
| |
QVR | Contrast adjustment value | <pl> |
| |
QVS | Sharpness adjustment value | <pl> |
| |
QWR | White balance: R adjustment value | <pl> |
| |
QWG | White balance: G adjustment value | <pl> |
| |
QWB | White balance: B adjustment value | <pl> |
| |
QHP | Horizontal position adjustment value | <pl> |
| |
QVP | Vertical position adjustment value | <pl> |
| |
QCP | Clock phase adjustment value | <pl> |
| |
QDC | Dot clock adjustment value | <pl> |
| |
QSP | Projection method status | <pl> |
| |
QLG | <pl> |
| ||
QXG | Wide mode status | Off | <0> |
|
|
| On | <1> |
|
|
| Auto | <0> |
|
QVX:DLVI0 | Daylight View status | Off | <+00000> | |
|
| Auto | <+00001> | |
|
| On | <+00002> | |
QPM | Picture mode status | Natural | <NAT> |
|
|
| Standard | <STD> |
|
|
| Cinema | <CIN> |
|
|
| Dynamic | <DYN> |
|
|
| Blackboard | <BBD> |
|
QFZ | Freeze status |
| <off_on> | |
Q$L | Lamp run time |
| <acctch> | |
QSH | Shutter function status |
| <off_on> | |
QKS | Keystone correction status | <pl> |
| |
QTE | Color temperature adjustment status | <color | temp> | |
QGD | Date setting status |
| <date> |
|
QGT | Time setting status |
| <time> |
|
As of October 2008 |
| < 10 > |
