Panasonic RQT7114-2Y, SLDZ1200 Changing the sound, Changing sound to simulate analog, Formance

Changing the sound

Before use

•Switch [PLAY SELECT] to select the media to be used

•Turn [MODE] on the rear panel to TURNTABLE

•Insert the SD Memory Card or CD to be used

Changing sound to simulate analog

	You can change CD or SD Memory Card audio to simulate an analog
operations	turntable.
	1 Press [VINYL SIM]
	•The VINYL SIM lamp lights.
	•During play, the sound changes to the type that has been
Advanced	set.
	2 To select the type
	Press [– + TYPE] to select the type
	•Analog simulation type: TYPE 1 to TYPE 8
	1 SL1200: Like using a SL1200 analog turntable
	2 MAKE UP: Like using a cartridge that emphasizes high
	and low range sounds
	3 WIDE RANGE: Like using a cartridge with wide range char-
	acteristics
	4 VIVID: Like using a cartridge with vivid characteristics
	5 LOW RANGE: Only low range sound is output producing
	a muffled sound
	6 HIGH RANGE: Only high range sound is output producing
	a crisp sound
	7 OLD RADIO: Like listening to an old radio
	8 TELEPHONE: Like speaking on an analog telephone
	•If no buttons are pressed for more than 5 seconds, the dis-
	play returns to its original state.
	•This feature simulates the fine acoustic characteristics of an ana-
	log turntable’s cartridge. Depending on the external equipment
	connected, the difference between analog simulation types may
	be difficult to notice.
	•You can use together with DYNAMIC FX.
	•Press [VINYL SIM] again to cancel.
	•The set type for each CD or SD Memory Card is stored to memory,
	and the setting is restored once the set media is re-inserted.
	Change sound with combined per-
	formance
	You can change the sound when using the platter slip surface.

1 Press [DYNAMIC FX]

•The DYNAMIC FX lamp lights.

20 •During play, the sound changes to the type that has been

RQT7114set.

2 To select the type

Press [– + TYPE] to select the type

•Special effect types: TYPE 1 to TYPE 8

1 ONE WAY: Generates sound only when the platter slip surface is operated in the forward direction.

2 TT DIST: Distorts the sound. The depth of the distortion can be changed using the platter slip surface.

3 TT WAH: Introduces a Wah Wah effect.

4 AIR HAMMER: Changes the sound intermittently

5 TT PAN: Changes the sound image from left or right by use of the platter slip surface.

6 AUTO PAN: Automatically rolls the sound image from left or right and back.

7 CRUSH RING: Distorts the sound. The speed of distortion can be changed by using the platter slip surface.

8 RING STORM: Sound simulates ringing of the wind.

•If no buttons are pressed for more than 5 seconds, the dis- play returns to its original state.

•Effects are different in the CD PLAYER mode, and there are also some effect types that are not output unless the platter slip surface is being rotated.

•You can use together with VINYL SIM.

•Press [DYNAMIC FX] again to cancel.

•The set type for each CD or SD Memory Card is stored to memory, and the setting is restored once the set media is re-inserted.

Editing the SAMPLE PADS

You can edit the start point or end point and volume of data recorded to SAMPLE PADS.

1 Press [SAMPLE EDIT] and select the item to be edited

Each time you press the button:

START	END	LEVEL	EDIT WRITING
		PLAY MODE SELECT	OK?

START : Beginning of data segment (START lamp indicator lights)

END : Ending of data segment (END lamp indicator lights)

LEVEL : Volume (START and END lamp indicators light)

PLAY MODE SELECT : (When selecting the play mode)

EDIT WRITING OK? : (Select to store to memory or not)

2 Press one of the recorded [SAMPLE PADS 1-4]

•The selected sample pad plays and the sample pad lamp flashes.

3 Press [– + TRIM] to change the data

•Time or level appears in the display.

•Smallest unit of adjustment

START, END	: 1 frame (1 sec. per 75 frames)
LEVEL	: 1 dB (–24dB to + 24 dB)

•Pressing selected sample pads while editing confirms changes.

•Sound may be distorted if the LEVEL is too high.

•If data is trimmed and stored, you cannot restore to the origi- nal length.

4 Modifying other data

•Perform steps 1-3 indicated above.

5 Storing to memory

Press [MEMORY]

•“COMPLETED” appears in the display and all sample pad data is stored.

•The selected sample pad lamp lights and the lamp of the edit item goes out.

Not storing to memory

Press [SAMPLE EDIT] to select “EDIT WRITING OK?”,

And press [+ ] to select “NO” from the display

•The lamp of the selected sample pad changes to a station- ary light, and the original data is returned.

•Pressing [– ] to select “YES” from the display will store to memory.