705102 REGGIE WHITE ALL PRO GYMASSEMBLY INSTRUCTIONS

1.Attach two 2" COVERCAPSand one 2" END CAPto BASEas shown on drawing.

2.Insert one 3 x 2" ENDCAPinto each end of TOPBOOMas shown on drawing.

3.Attach one 2" ENDCAPand one 1-1/4 x 5" GRIP to each PRESSARM.

4.Insert one 2" ENDCAPinto each end of LEG EXTENSIONas shown on drawing.

5.Insert one 2" ENDCAPinto open end of SEAT SUPPORTAffix. one 1-1/4" Rubber Bumperto SEATSUPPORTas shown on drawing.

6.LOOSELYassemble the UPRIGHTto the BASEas shown on drawing using two 3/8 X 3 bolts, two 3/8 locknuts and four 3/8 flat washers.

Makesure the edge of the UPRIGHTis flush with the side of the BASEand the bolts are oriented correctly.

7.LOOSELYassemble one PULLEYto the SEAT SUPPORTas shown in drawing using one 3/8 X 3 bolt, one 3/8 locknut and two 1/2 spacers.

8.LOOSELYassemble the SEATsuPPORT to the BASEand UPRIGHTas shown in drawing using three 3/8 X3 bolts, four 3/8 flat washers and three 3/8 locknuts.

9.Route CABLE6571001 thru inside of TOP BOOMas shown in Detail A. SECURELY, assemble two PULLEYSto inside of TOP BOOMusing two 3/8 X2-3/4 bolts, two 3/8 locknuts and four 3/8 flange spacers. Makesure cable is routedthru groovein pulleys.

DETAILA

10.SECURELYassemble TOP BOOMto UPRIGHTusing two 3/8 X 2-3/4 bolts and two 3/8 locknuts. Makesure cable runs over top of bolts.

11.Insert two WEIGHTPLATEBUSHINGSinto each WEIGHTPLATEas shown in Detail B.

12.SECURELY TIGHTEN ALL CONNECTIONS AT THIS TIME.

13.Slide WEIGHTSTACKCUSHIONSonto GUIDERODSand then insert into BASE.

14.CAREFULLYslide fifteen WEIGHTPLATES onto GUIDERODSwithkeyhole facing towards front of machine.

15.Assemble HEADPLATE and SELECT SHAFT using one 3/8 X 1-3/4 bolt, one 3/8 lock washer and one 3/8 flat washer. Slide I~iADPLATE onto GUIDERODS.

16.Attach GUIDERODSto TOP BOOMusing two

BLACK NYLONBOLTS.

17.Attach LEG EXTENSIONand ROLLERPAD SWIVELto SEATSUPPORTas shown in drawing, using one 3/8 X3-3/4 bolt, one 3/8 low ht. locknut, two 3/8 flat washersand two 3/8 flange spacers.

(TIGHTEN THE CONNECTIONENOUGHTO REMOVETHE PLAY, YET ALLOWINGTHE LEG EXTENSIONTO MOVEI:REELY.)

SECURELYattach SEAT and BACKPADto SEATSUPPORTand UPRIGH'fusing four 3/8 X2-3/4 bolts, four 3/8 lockwashersand two 3/8 flat washers.

19.To attach PRESS ARMASSEMBLYto BASE, follow assemblydrawingand these steps:

Insert two 3/4 flange bearings into BASE.

Loosely attach PRESSARMSt¢, the BASE using one 3/4 X5 bolt and 3/4 jam nut. (NOTE:Lay armson floor with grips in front of Leg Extension.)

Rotate one PRESSARMinto place, then LOOSELYattach the CROSSBRACEusing two 3/8 X2-3/4 bolts, two 3/8 fiat washersand two 3/8 locknuts. (NOTE:Make, sure CROSS BRACEis resting on the RUBBERBUMPER of the SEATSUPPORT.)

Attach other PRESSARMto CROSSBRACE using two3/8 X2-3/4 bolts, two 3/8 flat washers and two 3/8 locknuts.

IN THISORDER,tighten the 3/d X 5 bolt of the PRESSARMStogether, center (;ROSS BRACE andtighten bolts.

(TIGHTEN THE CONNECTION ENOUGHTO REMOVETHE PLAY, YET ALLOWINGTHE PRESS ARMSTO MOVEFREELY.)

DETAIL B

6587901

4

03/01/96

Page 5
Image 5
ParaBody 705102 Reggie White ALL PRO Gymassembly Instructions, Detaila, Securely Tighten ALL Connections AT this Time