Patton electronic 2703 user manual Terminal DTE Interface Cables, Patton Part Number

APPENDIX C (cont’d)

PATTON MODEL 2703

FACTORY PARTS AND ACCESSORIES

C-3 Terminal (DTE) Interface Cables

No terminal (DTE) cable is supplied with the Model 2703. You may construct your own cable using the pin-out diagrams in Appendix B, or purchase one of the Patton’s standard adapter cables listed below. Custom lengths are available.

Note: The part numbers below are completely distinct from the model number/suffix combinations shown on the previous page. Do not combine these part numbers with the model number of the stand- alone unit when ordering. These are separate items.

Patton Part Number	Cable Description (Interface)
2703-26M/35M	UD-26 male to M/34 male, 6 ft (V.35)
2703-26M/35F	UD-26 male to M/34 female, 6 ft (V.35)
2703-26M/15M	UD-26 male to DB-15 male, 6 ft (X.21)
2703-26M/15F	UD-26 male to DB-15 female, 6 ft	(X.21)
2703-26M/15F	UD-26 male to DB-37 female, 6 ft	(V.36)
2703-26M/36F	UD-26 male to DB-37 female, 6 ft	(V.36)
2703-26M/25M	UD-26 male to DB-25 male, 6 ft (EIA-530)
2703-26M/25F	UD-26 male to DB-25 female,6 ft (EIA-530)
N/A	Male UD-26 connector assembly
	Amp 749621-2 and 749608-1
	(both parts required)

Copyright © 1998

Patton Electronics Company

All Rights Reserved

19

APPENDIX D

SAFETY WARNINGS AND REQUIREMENTS

These warning notices apply to the Input Port, the port marked “Network”.

Warning: The port marked “SAFETY WARNING: see instructions for use” does not provide isolation sufficient to satisfy the requirements of BS6301; apparatus connected directly to this port should either have been approved to BS6301 or have previously been evaluated against British Telecommunications plc (Post Office) Technical Guides 2 or 26 and given permission to attach. Any other usage will invalidate the approval of the Interface Module.

Interconnection of the Interface Module (the port marked “Network”) directly, or by way of any other apparatus, with ports on other apparatus (marked or not so marked) may produce hazardous conditions on the network. Users should seek advice from a compe- tent engineer before such a connection is made.

The Interface Module is approved as a Host Independant Appliqué. As such the Interface Module is only approved for use with a host, and with host attachments, that are either type approved in their own right, or, if supplied after March, 1989, are covered by terms of the General Approval number NS/G/1234/J/100003. A Host sup- plied under the terms of the General Approval number NS/G/1234/J/100003 satisfies the conditions of the paragraph above.

The Interface Module must not be modified in any way. Any form of modification invalidates the approval for connection, and the Patton warranty of the unit.

The terms of the approval require that there must be a minimum distance (5mm) between the Interface Module and any other part of the host, including other Interface Modules. This condition is met by default when the Appliquè is installed in a Patton enclosure in accor- dance with the instructions. If voltages greater than 250V are present in the host , users should refer to a competent safety engineer for advice.

It is a condition of the approval that a copy of these user instruc- tions and safety warnings must be supplied with the host. Failure to provide the Interface Module user instructions with the host will invali- date the Appliquè approval.

Failure to install the Interface Module in accordance with these instructions will invalidate the approval. If you experience difficulties, or are in any doubt, please contact your Patton representative.

20