P L E A S E R E A D A N D S AV E T H E S E
I M P O R TA N T S A F E T Y I N S T R U C T I O N S
F E AT U R E S - O P E R AT I O N S
C L E A N I N G / M A I N T E N A N C E
T R O U B L E S H O O T I N G
Thank you for purchasing this Patton® product. We understand the value of quality and are committed to making superior products that stand the test of time. We trust this product will exceed your expectations of quality and reliability. We hope that you enjoy this product and will consider purchasing another Patton® product in the future.
To see our full product line or if you have any questions or comments about this product, please visit our website at: www.pattonproducts.com.
When using electrical appliances, basic safety precautions should always be followed to reduce the risk of fire,
9. | DO NOT insert or allow foreign objects to enter any |
| ventilation or exhaust opening as this may cause an |
10. | electric shock or fire, or damage the heater. |
DO NOT operate heater with a damaged cord or | |
| plug, or after the heater malfunctions, has been |
| dropped or damaged in any manner. Return |
| appliance to manufacturer for examination, electrical |
11. | or mechanical adjustment, or repair. |
A heater has hot and arcing or sparking parts inside. | |
| DO NOT use it in areas where gasoline, paint, or |
12. | flammable liquids are used or stored. |
Use appliance only for intended household use as |
PLEASE READ AND SAVE THESE IMPORTANT SAFETY INSTRUCTIONS
TECHNICAL SPECIFICATIONS
•Wattage: 1500W (+5%
•Working voltage: 120V AC/60Hz
PRE-OPERATING INSTRUCTIONS
1.Carefully remove your heater from the box. (please save the carton for
2.Make sure the unit is in the OFF position before plugging the heater into the outlet.
3.Place heater on firm level surface.
4.Avoid overloading your circuit by not using other high wattage appliances in the same outlet. At 1500 Watts, this unit draws 12.5 Amps.
NOTE: THIS UNIT IS FOR FLOOR USE ONLY
CLEANING/MAINTENANCE
DURING SEASON CARE:
1.Always unplug the heater before cleaning.
2.Clean the unit with a soft cloth moistened with a mild soap solution.
3.NEVER use abrasive or flammable solvents to clean the unit.
4.After cleaning, be sure to completely dry the unit with a cloth or towel.
AFTER SEASON CARE:
TROUBLESHOOTING
If your heater fails to operate:
• UNPLUG THE UNIT. |
• Make sure the electrical outlet or circuit breaker is |
working. |
• Check for obstructions. If you find an obstruction |
turn the heater OFF, and unplug the unit. Carefully |
remove the obstruction and follow the reset |
instructions. |
• The temperature may be set too low. Turn the |
temperature knob clockwise until the heater restarts. |
electric shock, and injury to persons, including the following:
1.Read all instructions before using the appliance.
2.To avoid fire or shock hazard, plug the appliance directly into a 120V AC electrical outlet.
3.The heater is hot when in use. To avoid burns, DO NOT let bare skin touch hot surfaces. If provided, use handles when moving this heater. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, and curtains at least 3 ft (0.9 m) from the front of the heater and keep them away from the sides and rear.
4.DO NOT run cord under carpeting. DO NOT cover cord with throw rugs, runners, or the like. Arrange cord away from traffic area and where it will not be tripped over.
5.This heater is not intended for use in bathrooms, laundry areas and similar indoor location. NEVER locate heater where it may fall into a bathtub or other water container.
6.Extreme caution is necessary when any heater is used by, or near children or invalids, and whenever the heater is left operating and unattended.
7.Always unplug the heater when not in use.
8.When unplugging, be sure to pull by the plug and not the cord.
| described in this manual. Any other use not |
| recommended by the manufacturer may cause fire, |
| electric shock, or injury to persons. The use of |
| attachments not recommended or sold by the |
13. | manufactuer may cause hazards. |
DO NOT use outdoors. | |
14. | To prevent a possible fire, DO NOT block air intakes or |
| exhaust in any manner. DO NOT use on soft surfaces, |
15. | like a bed, where openings may become blocked. |
To disconnect heater, turn controls to OFF, then | |
16. | remove plug from outlet. |
Avoid the use of an extension cord because the | |
| extension cord may overheat and cause a risk of fire. |
| However, if you have to use an extension cord, the |
| cord shall be No. 14 AWG minimum size and rated |
17. | not less than 1875 watts. |
If the heater will not operate, see specific instructions | |
18. | on Auto Safety |
DO NOT attempt to repair or adjust any electrical or | |
| mechanical functions on this unit. Doing so will void |
| your warranty. The inside of the unit contains no user |
| serviceable parts. All servicing should be performed |
19. | by qualified personnel only. |
Discontinue use if plug or outlet is hot. It is | |
| recommended that the outlet be replaced if plug or |
| outlet is hot to touch. |
AUTO SAFETY
TIP-OVER PROTECTION
This heater is equipped with a Total Safety System with
TIP-OVER SHUT-OFF:
When the unit is accidentally knocked over, it will shut off. To reset, simply place the heater in an upright position on a level surface.
OVERHEAT SHUT-OFF:
When a potential overheat temperature is reached, the system will automatically shut the heater off and the caution light will illuminate. Make sure heater is clear of all obstructions.
RESET INSTRUCTIONS:
If the unit shuts down:
1.Turn MODE to OFF (O) and THERMOSTAT to HI (•).
2.Unplug unit, wait 10 minutes.
3.Plug in and turn ON.
OPERATING INSTRUCTIONS
1.For heater operation, please set the Temperature all the way to HI (•).
2.Turn the Selector Control to desired heat setting (LO
(I)for 750W or HI (II) for 1500W).
3.The Power Light will remain lit during operation.
SETTING THE TEMPERATURE
1.You need to set temperature on HI (•) to start heater. Allow heater to operate and warm up the room.
2.When the desired temperature/comfort level is reached, lower the temperature setting until the heater stops operating.
3.The control will now automatically maintain the
NOTE: It is normal for the heater to cycle ON and OFF as it maintains the preset temperature. To prevent the unit from cycling, you need to raise the temperature setting.
1.Store heater in a cool, dry location
2.The manufacturer recommends that you store the unit in its original carton.
• Make sure selector is in LO (I) or HI (II) setting. |
Please DO NOT attempt to open or repair the heater. |
Please see the Warranty for Service Instructions or call consumer service at
THIS PRODUCT IS EQUIPPED WITH A 3-PRONG PLUG
This product is for use on 120 volts. The cord has a plug (A) as shown. An adapter
(C) (not included) is available for connecting
