![](/images/new-backgrounds/1039467/394673x1.webp)
Radiation angle measured at -6 dB point of polar response:
500 Hz to 1.6 kHz:
Horiz. | 145° +/- 55° |
Vert. | 165° +/- 100° |
1.6 kHz to 5 kHz: | |
Horiz. | 115° +/- 65° |
Vert. | 110° +/- 70° |
5 kHz to 16 kHz: | |
Horiz. | 95° +/- 15° |
Vert. | 95° +/- 15° |
Directivity factor, Q (Mean):
5.93 +/- 3.06
Directivity index, Di (Mean):
7.03 dB +/- 2.65 dB
Transducer complement:
Low Frequency Section:
one 6.5" premium Peavey woofer High Frequency Section:
Peavey 14XT™ titanium diaphragm compression driver on a 90° H x 90° V conical horn
Box tuning frequency:
Low Frequency Section:
100 Hz
Harmonic distortion:
1% rated power Second Harmonic:
100 Hz: | 0.54% |
1 kHz: | 0.25% |
Third Harmonic: |
|
100 Hz: | 1.97% |
1 kHz: | 0.46% |
10% rated power |
|
Second Harmonic: | |
100 Hz: | 0.98% |
1 kHz: | 0.66% |
Third Harmonic: |
|
100 Hz: | 2.45% |
1 kHz: | 0.66% |
Crossover frequency (internal passive): Low Frequency - High Frequency:
2.4 kHz
Impedance (Z): Full Range: Nominal: 8.0 Ω Minimum: 8.5 Ω
Input connection:
One
Enclosure materials & finish:
Trapezoidal,
Mounting provisions:
(1)Mounting bracket and associated hardware for attaching to SSE 6. This bracket will allow for horizontal mounting to walls and ceilings.
(4)
Dimensions (H x W x D):
Front:
16.41" x 9.95" x 9.47"
417 mm x 253 mm x 240 mm Rear:
16.41" x 5.23" x 9.47"
417 mm x 133 mm x 240 mm
Net weight:
21 lbs. (9.5 kg)
Frequency response
This measurement is useful in determining how accurately a given unit reproduces an input signal. The frequency response of the SSE 6 is measured at a distance of
Directivity
Beamwidth is derived from the
Power handling
There are many different approaches to power handling ratings. Peavey rates this loudspeaker system's power handling using a
Harmonic distortion
Second and third harmonic distortions vs. frequency are plotted in figures 5 & 6 for two power levels. Ten percent (10%) of rated input power and either one percent (1%) of rated input power or 1 Watt, whichever is greater. Distortion is read from the graph as the difference between the fundamental signal (frequency response) and the desired harmonic. As an example, a distortion curve that is down 40 dB from the fundamental is equivalent to 1% distortion.
Mounting
Caution: Before attempting to mount this speaker, consult a certified structural engineer. The speaker may fall due to improper installation, resulting in serious injury and property damage. DO NOT suspend or mount any other product or device from this SSE 6 enclosure. The maximum enclosure angle 45°. Use only Grade 5 hardware or better. All associated rigging is the responsibility of others.
Architectural & engineering specifications
The loudspeaker system shall have an operating bandwidth of 100 Hz to 17 kHz. The nominal output level shall be 90.0 dB when measured at a distance of 1 meter with an input of 1 Watt. The nominal impedance shall be 8.0 ohms. The maximum continuous power handling shall be 75 Watts, with maximum program power of 150 Watts, a peak power input of at least 300 Watts and a minimum amplifier headroom of 3 dB. The nominal radiation geometry shall be 120 degrees in the horizontal plane and 130 degrees in the vertical plane. The outside dimensions shall be 16.41 inches high by 9.95 inches wide by 9.47 inches deep. The weight shall be 21 lbs. The loudspeaker system shall be a model SSE 6.
3 + 2 YEAR LIMITED WARRANTY
NOTE: For details, refer to the warranty
statement. Copies of this statement may be obtained by contacting Peavey Electronics Corporation, P.O. Box 2898, Meridian, Mississippi
2