C A 6 - X P OW E R A M P L I F I E R
P R E L E I M I N A RY S P E C I F I C AT I O N S
| 1kHz, 0.01% THD+N | |
8Ω Stereo Power | 400W | 350W |
4Ω Stereo Power | 600W | 500W |
8Ω Bridged Mono Power | 1200W | 1000W |
Max RMS Output Voltage (each channel) | 73V |
|
Peak Output Voltage (each channel) | 103V |
|
|
|
|
Frequency Response (+0 / |
| |
Power Bandwidth (rated power at 4Ω , 1% THD+N) |
| |
|
| |
TourClass® Protection | ACL, IGM, AutoRamp, short circuit, DC voltage, | |
| ||
THD+N (rated power at 4Ω , 1kHz) | <0.01% |
|
|
|
|
SMPTE IMD (rated power at 8Ω , 60Hz & 7kHz) | <0.01% |
|
Damping Factor | 400:1 |
|
Input CMRR (1kHz) | > - 60dB |
|
|
| |
Input Sensitivity (rated power at 8Ω ) | 1.40V standard (see table below) | |
Voltage Gain | X37.7 standard (see table below) | |
Input Impedance (balanced/unbalanced) | >20kΩ />10kΩ |
|
Hum and Noise (“A” weighted, full power, 4Ω ) |
| |
|
|
|
Crosstalk (“A” weighted, full power, 4Ω ) | > - 60 dB |
|
Class | H |
|
|
| |
Input Connectors (per channel) | Female XLR (pin 2+, dealer configurable for pin 3+), TRS (tip+) | |
|
| |
Output Connectors (per channel) | ||
|
|
|
Filter Storage | 68,000 µF |
|
Power Supply (factory configured) |
| |
Idle Current Draw 120V | 1.6A |
|
|
|
|
1/8 Power Curr. Draw (typical music, 120V/4Ω ) | 6A |
|
1/3 Power Curr. Draw (continuous music, 120V/4Ω ) | 13.0A |
|
Max Curr. Draw (circuit breaker rating, 120V/4Ω ) | 21A |
|
|
|
|
Thermal Emissions (1/8 Power, 4Ω ) | 2630 BTU/hr |
|
|
|
|
Thermal Emissions (1/3 Power, 4Ω ) | 3713 BTU/hr |
|
Cooling | ||
| (filters removable without tools) | |
Controls | Front Panel: 2 attenuators, located behind blanking plugs | |
| Rear Panel: signal ground lift switch, mode select switch | |
|
| |
LED Indicators (per channel) | Clip/Limit, Signal, Temp/DC, Active | |
Construction | Steel chassis, 16 gauge. Double thickness in rack ear areas. | |
Dimensions (Height x Width x Depth) | 3.5" x 19" x 18" / 89 x 483 x 457mm | |
Gross Weight, Net Weight | 49 lbs. / 22.25 kg., 44 lbs. / 19.98 kg. | |
|
|
|
Warranty | 5 years* |
|
|
| Gain | Sens |
|
Factory Standard | X37.7 | 1.40V |
| |
| Option 1 | X40.0 | 1.32V |
|
| Option 2 | X20.0 | 2.65V |
|
| Rear View, |
|
|
|
| Binding Post | CAUTION | + | A |
| RISK OF ELECTRIC SHOCK | |||
|
| DO NOT OPEN |
| |
|
| AVIS : RISQUE DE CHOC |
|
|
Power figures are watts per chan- | Version |
| + | A |
|
| B | ||
nel, both channels driven. |
|
| + |
|
* |
|
|
| |
|
|
| B | |
tional years if Registration Card |
|
|
|
|
is sent to Crest Audio. (USA, |
|
|
|
|
Canada, United Kingdom, and |
|
|
|
|
many other countries). | Rear View, |
|
|
|
Crest Audio reserves the right to |
|
| NL4FC | |
Speakon |
|
|
| |
make improvements in manufac- |
|
| A | |
turing or design which may affect | Version |
|
|
|
specification. |
| A |
| |
Crest Audio specification litera- | (not available in |
|
| |
| B |
| ||
ture is available in downloadable | North America) |
|
|
|
PDF format; visit our website at: |
|
|
| B |
http://www.crestaudio.com. |
|
|
|
|
©1997 Crest Audio Inc. |
|
|
|
|
Architect’s & Engineer’s Specifications
The power amplifier shall have two channels. At 8 ohms, 20Hz
-20kHz, 0.1% THD+N, it shall deliver a minimum of 350 watts per channel. At 4 ohms, 20Hz - 20kHz, 0.1% THD+N, it shall deliver a minimum of 500 watts per channel. In bridged mono mode with an 8 ohm load, 20Hz - 20kHz, 0.1% THD+N, it shall deliver a minimum of 1000 watts.
The amplifier shall have circuitry to protect itself from output short circuits, thermal overload or other adverse load condi- tions. The amplifier shall protect speaker loads from DC volt- age on outputs. The amplifier shall have active clip limiting and impedance sensing circuitry. Output relays shall protect the speakers from amplifier failure.
Two rear panel mounted variable speed DC fans (filters detachable without tools) shall provide back to front air flow through the chassis.
Each channel shall have a standard
put stage. The frequency response shall be
The amplifier will operate at
Front panel indicators shall include Active, Protect, Signal, and Clip LED’s for each channel. Front panel attenuators shall be detented and located behind blanking plugs.
Rear panel input connectors shall be female TRS and XLR type, internally
A
The packaging of the amplifier shall allow for standard rack mounting without requiring space between similar units. Optional rack mount handles will be available. Dimensions shall be 19" (483mm) wide, 3.5" (8.9mm) high and 18" (457mm) deep. The amplifier shall weigh 44.0 lbs. (19.98 kg.) net, and shall be designated the Crest Audio model
AA
Designed & manufactured in the USA by:
• | • |
A B | Crest Audio Inc. |
A | 100 Eisenhower Dr. |
Paramus, New Jersey 07652 USA |
|
|
| + |
|
A B | A | B | • • |
|
|
| |||
| A | B | B |
|
|
|
| 1 | 2+ |
|
|
|
| 3- |
|
|
|
| |
|
|
| A |
|
| A |
|
| Designed & manufactured in the USA by: |
| A B | • • | Crest Audio Inc. | |
A |
| |||
| 100 Eisenhower Dr. | |||
|
|
|
| Paramus, New Jersey 07652 USA |
|
|
| + |
|
A B | A | B | • • |
|
|
| |||
| A | B | B |
|
|
|
| 1 | 2+ |
|
|
|
| 3- |
Crest Audio Inc.
100 Eisenhower Dr., Paramus NJ 07652 USA TEL: 201.909.8700 FAX: 201.909.8744 http://www.crestaudio.com
v. 1.0 08/13/97 | *B5000017* |
|