Pelco C1503M, C1510M-QS SECTION 3 OPERATION, 1.0 LOCAL SAT OPERATIONS

OPERATION CM9760-SAT 3-1

SECTION 3 OPERATION1.0 LOCAL SAT OPERATIONS

1.1 SELECTING MONITORS

1. Enter the monitor number (1-4) you want

to view.

2Press the MON button. The monitor num-

ber entered should match that appearing

in the keyboard LED display

1.2 SELECTING CAMERAS

1. Enter the camera number (1-16) you want

to view.

2. Press the CAM button. The camera view

appears on the selected monitor.

1.3 CONTROLLING CAMERAS

1.3.1 Multi-Speed PAN and TILT

Control, KBD200

Use the KBD200’s “Touch Speed” feature to op-

erate pan and tilts equipped with variable-

speed.

Enter a number between 1 (slowest) and 9 (fast-

est) followed by one of the pan and tilt buttons.

The selected speed remains in the switcher’s

memory until it is changed. Entering zero re-

sets the pan and tilt speed to about 20 degrees

per second.

1.3.2 Variable-Speed PAN and TILT

Control, KBD300/KBD300V

Use the joystick to operate variable-speed pan

and tilt control from the KBD300/KBD300V.

Pan and tilt response increases as the joystick

is deflected from its normal position. Slight de-

flection causes slow pan and tilt response while

full deflection causes rapid response.

1.3.3 Step Through System Camera

Use the PREV (backward) and NEXT (for-

ward) buttons to step through the system cam-

eras, or those cameras partitioned for your key-

board location. The displayed camera order

does

NOT

follow that set up in the CAMERA

SEQUENCE sub-menu of the monitor pro-

gramming menu (see the Monitor Program-

ming Menu-Page 2 of 3). Those settings

effect sequence operations only. Instead, at

each press of the button, the SAT will stop, in

turn, at each video input on the unit. What you

see displayed is influenced by the following

items:

1. If any SAT input lacks a display source,

you will only see a blank screen. For ex-

ample, if the unit is supplied with input

video on 1 and 16 only and no other in-

puts, then pressing NEXT or PREV while

between these end-points will result in a

blank screen display. Moreover, you will

have to press the key 14 times to navi-

gate from either end to the other.

2. The situation in (1) can be avoided if the

MON to CAMERA sub-menu, located

in Section 2’s,

Access Programming

There is no indication on the keyboard display that you are actually viewing the

camera you chose. This can be rectified by entering appropriate camera titles for each cam-

era view when programming local

SAT

menus.

Figure 3-1

Monitor Selection

Figure 3-2

Camera Selection

Figure 3-3

Camera Step-Through

1.0 LOCAL SAT OPERATIONS........................................... 3-1

Selecting Monitors ............................................................ 3-1

Selecting Cameras ........................................................... 3-1

Controlling Cameras......................................................... 3-1

Operating Sequences....................................................... 3-3

Controlling Auxiliaries ....................................................... 3-4

IMPORTANT: Initializing keyboards.

For

SAT SIDE

local operation, keyboards must be initialized (1) after any

power cycle or (2), after the first time power is applied to a

keyboard or (3), after an operator initiated reset (see

Ap-

pendix 5

, Default Menu reset Assignments). To initialize a keyboard,

enter the number (1-4) of the monitor from which you are going to view

displays, then press the

MON

key. You must wait five seconds (before

or after you enter the number and press the

MON

key) to allow for power

up configuration to take place, after which the number of the selected

monitor appears on the keyboard’s

LED

display.

Up to 16 cameras and four monitors (minus those used as tie-lines) are

available for user access and control via keyboards connected to the SAT.

Access is limited by the following constraints:

1. Physical: a monitor must be available at your location.

2. Software: programmed access (local SAT programming menus)

for monitor/camera use must have been partitioned for access by

the user in question.

2.0 9760 SAT OPERATIONS............................................... 3-4

Selecting Link (Satellite) Cameras.…............................... 3-4

Controlling Link Cameras…………….. ............................. 3-5

Operating Suggestions………………................................ 3-5

3.0 ALARM OPERATIONS................................................... 3-6

Local SAT Alarm Response………................................... 3-6

9760 System-SAT Alarm Response….............................. 3-7

SAT and SAT-Alarm Unit configurations........................... 3-9