Place the mounting plate against the wall and
insert the toggle wings into the holes in the wall
to mount the plate.
NOTE: Before tightening toggle bolts and wood
screw, make sure the bottom of the mounting plate
touch the bottom of the cabinet when pushed
flush against the wall and that the plate is properly
centered under the cabinet.
CAUTION: Be careful to avoid pinching fingers
between the back of the mounting plate and the wall.
Tighten all bolts. Pull the plate away from the wall
to help tighten the bolts.
3
4
ATTACH THE MOUNTING
PLATE TO THE WALL
A1.
Attach the plate to the wall using toggle bolts.
At least one wood screw must be used to attach
the plate to a wall stud.
Remove the toggle wings from the bolts.
Insert the bolts into the mounting plate
through the holes designated to go into drywall
and reattach the toggle wings to 3⁄4″(19 mm) onto
each bolt.
1
INSTALLATION OVERVIEW
A1. Attach Mounting Plate to Wall
A2. Prepare Top Cabinet
Mount Microwave Oven
A5. Adjust Exhaust Adaptor
A6.
Wall
Mounting
Plate
Spacing for Toggles
More Than Wall
Thickness
Bolt End
Toggle
Bolt
Toggle Wings
To use toggle bolts:
Installation Instructions
2
OUTSIDE TOP EXHAUST (Vertical Duct)
A
IMPORTANTNOTES:
•Make sure the screws for the
blower motor and blower plate
are securely tightened when
they are reinstalled. This will
help to prevent excessive
vibration.
•Make sure the motor wiring has
been properly routed and secured,
and that the wires are not pinched.
A7.Connect Ductwork
A3.
A4. Check Damper Operation
Adapting Microwave Blower for
Outside Top Exhaust
EN-12
3/8"TOEDGE
%#76+10Ä+(':*#756#&#2614+5215+6+10'&1765+&'
4'%1//'0&'&&+/'05+10)4'#5'Ä.#&'0#+49+..
&+5%*#4)'+061*175'5647%674'
/+0+/7/9+&6*4'37+4'&
4'#49#..6'/2.#6'
NOTE: IT IS VERY IMPORTANT TO
READ AND FOLLOWTHEDIRECTIONS
IN THE INSTALLATION INSTRUCTIONS
BEFORE PROCEEDINGWITH THIS
REAR WALL TEMPLATE.
This RearWa
ll Template serves to position the bottom
mounting plateand to locate the horizontal exhaust
outlet.
1. Use a levelto check that the template is positioned
accurately.
2. Locate andmark at least onestud on theleft or
right side of the centerline.
016'
It is important to use at least one wood
screw mounted firmly in a stud to support the weight
ofthe microwave. Mark two additional, evenlyspaced
locations for the supplied toggle bolts.
3. Drill holes in the marked locations.Where there is
a stud, drill a 3/16" hole for wood screws. For holes
thatdo not line upwith a stud, drill 5/8" holes for
toggle bolts.
016'
DO NOT INSTALL THE MOUNTING PLATE
AT THISTIME.
4. Remove the template fromthe rear wall.
5.Reviewthe InstallationInstruction book for your
installation situation.
Locate and mark holes to align with holes in the
mountingplate.
IMPORTANT:
LOCATE AT LEAST ONE STUD ON EITHERSIDE OF
THE CENTERLINE.
MARKTHE LOCATIONFOR 2 ADDITIONAL, EVENLY
SPACED TOGGLE BOLTS IN THE MOUNTING PLATE
AREA.
Locate and mark holes to align with holes in the
mountingplate.
IMPORTANT:
LOCATE AT LEAST ONESTUD ON EITHER SIDE OF
THE CENTERLINE.
MARKTHE LOCATIONFOR 2 ADDITIONAL, EVENLY
SPACEDTOGGLE BOLTS IN THE MOUNTING PLATE
AREA.
Trim the rear wall template alongthe dotted line.
Trim the rear wall template alongthe dotted line.
%
(%76176(14*14+<106#.
1765+&'':*#756
%76*1.'6*417)*4'#49#..(14':*#756#&#2614
12"
4"
Darlevueltaalahojaparaconsultarla
versiónenEspañol.
IMPORTANT:Do not remove the cardboard
etween the heat shield and door.
spacers b