Philips 404939 manual Warnings, Cautions and Operating Instructions, Lamp Operating Instructions

Philips Lighting Company	www.philips.com	Philips Lighting
200 Franklin Square Drive		281 Hillmount Road
P.O.Box 6800		Markham, Ontario
Somerset, NJ 08875-6800		Canada L6C 2S3
1-800-555-0050		1-800-555-0050
A Division of Philips Electronics North America Corporation		A Division of Philips Electronics Ltd.
Updated 3/09	TDS-404939

MasterColor® Ceramic Metal Halide 22 Watt 3000K TubularSingle-EndedT4 Lamps with FadeBlock™ UV Filtering

Electrical Data (Subject to change without notice )

Lamp Watts (Nominal) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Lamp Operating Voltage (rms) (Nominal)2. . . . . . . . . . . . . 100

Initial Lamp Voltage Range (rms)3. . . . . . . . . . . . . . . . . . . . . 95–108

Lamp Operating Current (Amps) (rms) (Nominal) . . . . . 0.22

Lamp Current Crest Factor (Maximum) . . . . . . . . . . . . . . 1.8

Warm-up Time to 80% of Output . . . . . . . . . . . . . . . . . . . 3 Minutes

Restrike Time for Hot Lamp. . . . . . . . . . . . . . . . . . . . . . . . . 4–8 Minutes

Ballast Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C156/C175/E

Ballast Open Circuit Voltage (Minimum). . . . . . . . . . . . . . . 250

Pulse PeakVolts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3000 Min., 4000 Max.

Pulse Width @ 90% Peak . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Micro Second Min.

Pulse Repetition Rate (Minimum)4 . . . . . . . . . . . . . . . . . . . . 1 per Half Cycle

Minimum Operating Temperature. . . . . . . . . . . . . . . . . . . . -30ºC

1)Measured at 100 hours of life in vertical position.

2)Measured at rated lamp watts on a linear reactor. LPW does not include ballast losses.

3)Measured with the lamp operating at rated watts.

4)Option-Pulse Width @ 90% Peak, 1 micro second minimum with 2 pulses per half cycle.

INSTALLATION INFORMATION

MasterColor® Metal Halide T4 lamps must be used in combination with appropriate fully electronic ballast.

Warnings, Cautions and Operating Instructions

R“WARNING:These lamps can cause seriousskin burn and eye inflammation from short waveultravioletradiationif outer envelopeof the lamp is brokenor punctured.Do not use where people will remainfor more than a few minutesunless

adequateshieldingor other safetyprecautionsare used.Certainlamps that will automaticallyextinguishwhen the outer envelopeis brokenor puncturedare commerciallyavailable." This lamp complieswith FDA radiationperformance standard21 CFR subchapterJ. (USA:21CFR1040.30Canada:SOR/DORS/80-381)

If the outer bulb is brokenor punctured,turn off at once and replace the lamp to avoid possible injury from hazardousshort wave ultraviolet radiation.Do not scratch the outer bulb or subject it to pressureas this could cause the outer bulb to crack or shatter.A partial vacuum in the outer bulb may cause glass to fly if the envelopeis struck.

WARNING:The arc-tubeof metal halide lamps are designedto operate under high pressureand at temperaturesup to 1000ºC and can unexpectedlyrupturedue to internal or external factors such as a ballast failure or misapplication. If the arc-tube rupturesfor any reason,the outer bulb may break and pieces of extremely hot glass might be dischargedinto the surroundingenvironment.If such a rupture were to happen,THERE ISA RISK OF PERSONALINJURY,PROPERTY

DAMAGE,BURNSAND FIRE.

Certain lamps that will retain all the glass particles should inner arc-tube rupture occur are commercially available from Philips Lighting Company.

RELAMP FIXTURESATOR BEFORETHE END OF RATEDLIFE. Allowinglamps to operateuntil they fail is not advisedand may increase the possibilityof inner arc tube rupture.

This lamp contains an arc tube with a filling gas containing less than

10 nCi of Kr-85 and is distributed by Philips Lighting Company,a division of Philips Electronics North America Corporation, Somerset,

New Jersey,08875.

CAUTION: TO REDUCETHE RISK OF PERSONALINJURY,PROPERTY DAMAGE,BURNSAND FIRE RESULTINGFROMANARC-TUBERUPTURETHE FOLLOWINGLAMP OPERATINGINSTRUCTIONSMUST BE FOLLOWED.

Lamp Operating Instructions:

1) RELAMP FIXTURES AT OR BEFORE THE END OF RATED LIFE. Allowing lamps to operate until they fail is not advised and may increase the possibility of inner arc tube rupture.

2)Use only in fully enclosed fixtures capable of withstanding particles of glass having temperatures up to 1000°C. Lens/diffuser material must be heat resistant. Consult fixture manufacturer regarding the suitability of the fixture for this lamp.

3)Do not operate a fixture with a missing or broken lens/diffuser.

4)Operate lamp only within specified limits of operating position.

5) Before lamp installation/replacement, shut power off and allow lamp and fixture to cool to avoid electrical shock and potential burn hazards.

6)Use only auxiliary equipment meeting Philips and/or ANSI standards. Use within voltage limits recommended by ballast manufacturer.

A.Operate lamp only within specified limits of operation.

B.For total supply load refer to to ballast manufacturer’s electrical data.

C.Operate CDM-T6 (G12 base) lamps only on thermally protected ballasts.

D.Operate CDM-TC lamps (G8.5 base), CDM-T6 Elite lamps, and CDM-T6 39W/842 lamps only on thermally protected electronic ballasts.

7)Periodically inspect the outer envelope. Replace any lamps that show scratches, cracks or damage.

8)If a lamp bulb support is used, be sure to insulate the support electrically to avoid possible decomposition of the bulb glass.

9)Protect lamp base, socket and wiring against moisture, corrosive atmospheres and excessive heat.

10)Time should be allowed for lamps to stabilize in color when turned on for the first time. This may require several hours of operation, with more than one start. Lamp color is also subject to change under conditions of excess vibration or shock, and color appearance may vary between individual lamps.

11)Lamps may require 4–8 minutes to re-light if there is a power interruption.

12)Take care in handling and disposing of lamps. If an arc tube is broken, avoid skin contact with any of the contents or fragments.