Philips 653-103 setup guide TV and Remote Control Operation, Television

TV AND REMOTE CONTROL OPERATION

TELEVISION

Press the POWER/STANDBY button

to turn the TV on. Allow about 10 seconds for the TV power on.

Press the VOL (+) but-

ton to increase the sound level

or the VOL (–) button to

lower the sound level.

Pressing both buttons at the

same time will display the on- screen menu. After you are in the menu, use these buttons to make adjustments or selections.

Press the CH ▼ (down) or ▲ (up) button to select TV

channels. Use these buttons to make adjustments or selections in the on-screen menu.

NOTE: Press three number buttons on the remote control for channels 100 or above. For example: Press 1 then 2 then 5 for channel 125.

Point the remote control

toward the remote sensor win- dow on the TV to use the remote to operate the TV.

VOLCH

MENU

Remote Sensor

Window

REMOTE

BATTERY INSTALLATION

Battery Usage CAUTION—To prevent battery leakage which may result in bodily injury or damage to the unit:

2 3 1

•Install ALL batteries correctly, + and – as marked on the unit.

•Do not mix batteries: (OLD and NEW or CARBON and ALKALINE, etc.)

•Remove batteries when the unit is not used for a long time.

To load the supplied batteries into the remote:
1. Remove the battery compartment lid
on the back of the remote.
2. Place the batteries (2- AA) in the remote.
Be sure the (+) and (–) ends of the batteries line
up correctly (the inside of the case is marked).
3. Reattach the battery lid.
Sleep Button
Press to set the TV to automatically turn itself off. Press to
set the TV to automatically turn itself off after a period of
time. Choose 15, 30, 45, 60, 90, 120, 180, or 240 minutes
before the TV will automatically turn off.
A/V Button	TV
Press repeatedly to select the different signal sources con-	VCR
nected to the TV.
TV/VCR/ACC Mode Switch	ACC
Slide to position of TV to control TV functions, VCR to con-
trol VCR functions and ACC for cable converter, satellite
receiver, DVD, and laser disc accessory device functions.
i+ (on-screen display) Button
Press to see the current channel number on the TV screen.
Also press to clear the TV screen after control adjustments.
SmartSound Button
Press to select an SmartSound control. Choose from three
factory-set controls (VOICE, MUSIC, and THEATRE) and
a PERSONAL control that you set according to your own
preferences through the on-screen Sound menu. The three
factory-set controls will tailor the TV sound to enhance the
type of program you are watching.
Menu Button
Press for the on-screen menu to appear. Pressing the menu
button after menu selections are made will eliminate the
menu from the display.
Cursor Buttons (Left, Right, Up, Down)
Press these buttons to highlight, select, and adjust items on
the TV's on-screen menu.
Volume (+) or (–) Buttons
Press to adjust the TV sound level.
Mute Button
Press to turn the TV sound off. Press again to return the
sound to its previous level.
Incr. Surr. Button
Press to select various factory Surround Sound listening
modes.
PIP Buttons
Press to operate Picture-In-Picture features. See the PIP sec-
tion in the Directions for Use manual for details.

4

AVi+ SAP

1 2 3

4 5 6

7 8 9

SMART SMART

0

MENUSURF

CH

INCR. SURR. PIP A/CH

PIP CH

UPDN

SAP

AV

TV

VCR			SMART
	ACC		SURF
		SMART
			MENU

	CH
	A/CH
	PIP
.
.SURR
INCR	CH	DN
	PIP
	UP

Power Button

Press to turn the TV on and off.

SAP Button

Press to select Second Audio Program (SAP) if available with the program you are watching.

Clock Button

Press the CLOCK button to access the Timer menu, where you can manually set the clock.

Number Buttons

Press the number buttons to select TV channels. When selecting single-digit channels, press the number of the desired channel. The TV will pause for a few seconds and then tune to the selected channel. (Note: You can also press 0, then the number.) For channels 100 and above, first press 1 then the next two numbers of the desired channel.

SmartPicture Button

Press to select an SmartPicture control. Choose from four factory-set controls (MOVIES, SPORTS, WEAK SIGNAL, and MULTIMEDIA) and a PERSONAL control that you set according to your own preferences through the on-screen PICTURE menu. The four factory-set controls will tailor the TV picture to enhance the particular type of program you are watching or to improve the picture of a program with a weak broadcast signal.

Surf Button

Press to quickly view a list of up to 10 channels you have placed in memory. Go to the channels directly from the Surf screen. (Details are in the Directions for Use manual. )

CH(annel) Scan (+) or (–) Buttons

Press to change the tuned channel.

VCR ◀◀, ■, ▶, ▶▶, II Buttons

Press to rewind, stop, play, fast forward, or pause a videotape.

A/CH Button

Press to toggle between the currently viewed channel and the previously viewed channel.

SMART HELP

Remember, you can press any button on the front of the TV to turn the TV on.

The tuned channel number will always briefly appear on the screen when the TV is first turned on (and when the channel is changed).

You also can press the i+ button (on the remote con- trol) to see what channel the TV is on.

2