English | Controls / Power supply | |
|
|
|
Clock / Radio | CD player |
Controls (See 1)
1AL1/ AL2 indicator – lights up when ALARM 1 or ALARM2 is activated
2PM indicator
3ALARM 1 (OFF•SET•ON)
–switches on ALARM 1
–sets alarm time of ALARM 1
–switches off ALARM1
4REPEAT ALARM – switches off the alarm for a
5Display – shows the status of the set
6ALARM 2 (OFF•SET•ON)
–switches on ALARM 2
–sets alarm time of ALARM 2
–switches off ALARM2
7LIFT TO OPEN - lift here to open CD door
8TUNING - tunes to a radio station
9STOP 9 - stops CD playback
0PLAY/PAUSE 2; - starts or pauses CD playback.
!MIN ∞ / HOUR §
–adjusts the minute/hour for clock/alarm time
–skips or searches CD track/ passage backward/ forward
@FM•AM•BUZ•CD
–selects FM, AM or CD sound source
–selects radio, buzzer or CD alarm mode
#POWER/ ALARM RESET
–switches the set on/off
–stops the active buzzer, radio or CD alarm for 24 hours
–switches off the sleep timer
$SLEEP
–activates the radio/CD player for SLEEP function
–displays/adjusts/switches off sleep timer
% SET TIME – sets the clock time
^VOLUME - adjusts volume level
&Battery compartment – insert a 9 volt battery, type 6F22 (not supplied) for clock memory backup
*Power cord - connects to wall outlet.
(RESET – use a ballpoint pen to press RESET if the set/display does not react to any of the controls
Power Supply
1Check if the power voltage, as shown on the bottom of the set, corresponds to your local power supply.
2Connect the power plug to the wall outlet.. The power supply is switched on and 12:00 flashes on the display.You can set the clock now. (See Setting the clock)
3To switch off the set completely, withdraw the power cord from the wall socket.
Clock memory backup
When a power failure occurs, the set will be switched off completely. When the
power supply returns, 12:00 flashes on the display and you need to reset the clock.
To retain the clock/ alarm time in the event of AC power failure or disconnection, insert a 9 volt battery, type 6F22 (not supplied) into the battery compartment: it will act as clock memory backup. However, the time will not be illuminated on the display. Operation of the alarms, FM/AM radio and CD are also excluded. As soon as the power supply returns, the display will indicate the correct time.
1 Connect the power plug to the wall outlet.
2 Insert the battery into the battery compartment..
•Replace the battery once a year, or as often as necessary.
Batteries contain chemical substances, so they should be disposed of properly.
Setting the clock
Clock display
The display shows the time and also indicates whether you have switched on the alarm(s). The indicators light up next to AL1 and AL2 respectively.
The time is displayed using
1Press SET TIME once or more until the hour/minute digits flash.
➜ Display: 12:00 flashes by default.
2Hold down or press HOUR § / MIN ∞ repeatedly to adjust the hours and minutes respectively. Release HOUR § / MIN ∞ when you have reached the correct setting.
3Press SET TIME to confirm.
Important Note:
Press and hold SET TIME button will change the display from 12 hours to 24 hours.
Standby power consumption
(clock mode) | 1.0W |
Radio
1Press POWER to switch on.
➜POWER button lights up.
2Use FM•AM•BUZ•CD to select FM or AM waveband.
3Use TUNING (on the side panel) to find your station.
4Adjust the sound with the VOLUME control.
To improve reception:
FM: Extend and adjust power cord for optimum reception.
AM: Use the
5Press POWER to switch off.
➜POWER button light turns off.
CD playback
This set can play audio discs including
Do not try to play a
1Open the CD door.
2Insert a CD with the printed side facing up, and close the CD door.
3Press POWER to switch on.
➜POWER button lights up.
4Select CD source by using the FM•AM•BUZ•CD selector.
5Press PLAY/PAUSE 2; to start playback.
➜Display shows briefly current track number and returns to the clock display.
6Adjust the sound with the VOLUME con- trol.
7To interrupt playback, press 2;.
8Press 2; to resume playback.
