GENERAL INFORMATION / CD PLAY
In-car use (connections supplied or optionally available)
Only use the AY 3545 (4822 219 10033) or AY 3548 (3140 118 71890) car voltage converter (4.5 V DC, positive pole to the center pin) and the AY 3501 cassette car adapter. Any other product may damage the set.
CD PLAY / FEATURES
Playback information
•If a CD-Recordable (CD-R) or a CD-Rewritable (CD-
RW) is not recorded properly, NF dISC is displayed, indicating that the CD has not been finalized. In that case, use FINALIZE on your CD
1Put the set on a horizontal,
2Plug the voltage converter into the cigarette lighter jack (only for 12 V car battery, negative grounding), then connect the wired end with 4.5V DC input jack on the set.
12 V DC
4,5 V DC
recorder to complete the recording.
• When playing a
•Playback will stop if you open the CD lid.
•While the CD is read, 1
Volume and bass
3If necessary, clean the cigarette lighter jack to obtain a good electrical con- tact.
4Turn down the volume and connect the cassette adapter plug to LINE OUT/p on the set.
5Carefully insert the cassette adapter into the car radio’s cassette compartment.
6Make sure the cord does not hinder your driving.
7Decrease the volume on the set if necessary. Start playback on the set and adjust the sound with the car radio controls.
•Always remove the voltage converter from the cigarette lighter jack- when the set is not in use.
Note: If your car radio has a LINE IN jack, it is better to use it for the
car radio connection instead of the cassette.adapter. Connect the signal lead to this LINE IN jack and to LINE OUT/pon the set.
Playing a CD
This
1 Push the OPEN 2 slider to open the player.
2Insert an audio CD, printed side up, by pressing the
CD onto the hub.
3 Close the player by pressing the lid down.
4 Press 2; to switch the player on and start playback. yThe current track number and elapsed playing
time are displayed.
• You can pause playback by pressing 2;. yThe time at which playback was paused starts
flashing.
• You can continue playback by pressing 2; again.
5Press 9 to stop playback.
yThe total number of tracks and the total playing time of the CD are displayed.
6 Press 9 again to switch the player off.
• To remove the CD, hold it by its edge and press the hub gently while lifting the CD.
Note: If there is no activity, the set will automatically switch off after a while to save energy.
Volume adjustment
• Adjust the volume by using VOL +/−.
Bass adjustment
• Press DBB to switch the bass enhancement on or off
y
Remote control (for some versions only)
Use the AY 3768 / AY 3778 cord remote control.The but- |
|
tons on the remote control have the same functions as |
|
the corresponding buttons on the set. | p |
1 Press 9 twice to switch off the set.
2 Firmly connect the remote control to LINE OUT/pon the set.
3Adjust the volume on the CD player and remote control.
Selecting a track and searching
Selecting a track during playback
• Briefly press ∞ or § once or several times to skip to the current, previous or next track.
yPlayback continues with the selected track, and the track’s number is displayed.
Selecting a track when playback is stopped
1Briefly press ∞ or § once or several times to select the desired track. The track number is displayed.
2Press 2; to start CD play.
yPlayback starts with the selected track.
Searching for a passage during playback
1Keep ∞ or § pressed to find a particular passage in a backward or forward direction.
ySearching starts while playback continues at low volume. After 2 seconds the search speeds up.
2Release the button when you reach the desired passage. yPlayback continues from this position.
Notes: – If the player is in SCAN mode (see MODE chapter), searching is not possible.
–In shuffle, shuffle repeat all or repeat mode (see MODE chapter), or while playing a program, searching is only possible within the particular track.
