Philips AX 1101/10 bottom of the set, If you try to store more than 15 tracks, FULL is displayed

PLAYING A CD

This CD player can play all kinds of Audio Discs such as

CD-Recordables and CD-Rewritables. Do not try to play a

CD-ROM, CDi, VCD, DVD or computer CD.

1 Push OPEN 2 to open the CD compartment lid.

2Insert an audio CD, printed side up, by pressing the

CD center onto the hub.

3 Close the player by pressing the lid down.

MODE

4 Press 2; to switch the player on and start CD playback.

yThe current track number and the elapsed playing time are displayed.

•You can pause playback by pressing 2;.

yThe time where playback was paused will flash.

•You can continue playback by pressing 2; again.

5Press 9 to stop playback.

yThe total number of tracks and the total playing time of the CD are displayed.

6Press 9 again to switch off the player.

•To remove the CD, hold it by its edge and press the hub gently while lifting the CD.

Note: If there is no activity, the unit will automatically switch off after a while to save energy.

PLAYBACK INFORMATION

SELECTING A TRACK AND SEARCHING
Selecting a track during playback
• Briefly press ∞ or § once or several times to skip
to the beginning of the current, previous or next track.	MODE
yPlayback continues with the selected track, and	PROGRAM
its number is displayed.

Selecting a track when playback is stopped

1Briefly press ∞ or § once or several times. yThe selected track number is displayed.

2Press 2; to start CD play.

yPlayback starts with the selected track.

Searching for a passage during playback

1Keep ∞ or § pressed to find a particular passage in a backward or forward direction.

ySearching is started and playback continues at

low volume. After 2 seconds the search speed increases.

2Release the button when you reach the desired passage. yNormal playback continues from this position.

Notes: – During SHUFFLE, SHUFFLE REPEAT ALL, REPEAT or while playing a program, searching is only possible within the particular track.

PROGRAMMING TRACK NUMBERS

•If a CD-Recordable (CD-R) or a CD-Rewritable (CD-RW) is not recorded properly, nF dISC is displayed. In that case, use FINALIZE on your CD- recorder to complete the recording.

•If you want to play a CD-Rewritable (CD-RW), it takes 3–15 seconds for sound reproduction to start once you have pressed 2;.

•Playback will stop if you open the CD lid.

•While the CD is being read, 1 -:- flashes in the display.

VOLUME AND BASS

Volume adjustment

Adjust the volume by using VOL E.

Bass adjustment

• Press BASS to switch the bass enhancement on or off

You can select up to 15 tracks to play in a program. A single track may be played more than once in the program.

1While playback is stopped, select a track with ∞ or §.

2Press PROGRAM to store the track. yPROGRAM lights; the track number

programmed and P, with the total number of stored tracks, are displayed.

3Select and store all desired tracks in this way.

4Press 2; to start playback of your selected tracks. yPROGRAM is shown and playback starts.

•You can review the program by pressing PROGRAM for more than 2 seconds.

yThe display shows all stored tracks in sequence.

MODE PROGRAM

y	is shown if the bass enhancement is	MODE
		PROGRAM
	activated.

Both the model number and production number are located on the

bottom of the set.

Notes: – If you press PROGRAM and no track is selected, SELECt is displayed.

– If you try to store more than 15 tracks, FULL is displayed.

Clearing the program

• While playback is stopped, press 9 to clear program. yCLEAr is displayed once, PROGRAM

disappears, and the program is cleared.

Notes: – The program also will be cleared if you

–interrupt the power supply, or

–open the CD compartment lid, or

–if the unit switches off automatically.