Features for Suspended Modules

Lighting Systems F7000-17

1BHFPG

'4FSJFT-JHIU5-PVWFS4JEF-FOT

Armstrong®5FDI;POFÜ$PNQBUJCMF

5.770” (14.66cm)



1.63”			.750
1.63”			.750
(4.14cm)			(1.91cm)
(4.14cm)			(1.91cm)

1.304” (3.31cm)

Ordering Information

FamilySeries

F7			4

4 = Block w/ Lens

5.77” (14.66cm)

TypeLamps

	4			2
	4			2
	4 = Louver			2 = 2 Lamps

Color

AL = Aluminum WH = White

6.Louver Shielding

Wattage

Voltage

Length

Options

= 28W

1 = 120v

4 = 4’ (121.92cm)

X4 = 4 Through

= 54W

2 = 277v

8 = 8’ (243.84cm)

Wires

3 = 28W Dimming

X5 = 5 Through

= 28W EM

Wires

5 = 54W Dimming

DS = Dual Switch

Complete Ordering Instructions below.

6 = 54W EM

1.Housing: Single piece of high purity extruded aluminum, a portion from recy- cled material. Extruded acrylic lens reveal installed on the top of the housing, runs the length of the housing.

2.Housing End: Die-cast aluminum, welded in place.

3.End Cap: Die-cast aluminum. Encloses the suspension cable and power feed cord for the end of the run.

4.Lamps: F28T5 or F54T5HO as specified. By others. Installed from the ceiling side of the luminaire.

5.Ballast: Electronic. Meets ANSI starting, end-of-life protection and sound rat- ing specifications. Low THD.

6.Shielding: Integral, regressed flat louver blades punched and formed from fix- ture housing, finished to match, no light leaks. Blades are .56” (1.42cm) high on .75” (1.91cm) centers.

Electrical

Connections: 18 gauge pre-wired with polarized cannon plug connectors for simultaneous mechanical/electrical connection.

Emergency Battery Pack: 90 minute operation, 700 lumens for 54W and 520 lumens for 28W.

Dimming: Advance Mark X standard (no additional wires required); use compat- ible dimmer. Dimming ballasts using additional control wires (eg Lutron Hi-Lume or ECO-10, Osram) can be used; consult factory and use X4 or X5 power feeds with additional leads, as appropriate. Ballast not to exceed 1.25” (3.18cm) wide by 1.20” (3.05cm) high.

iGEN: F7000 accepts iGEN (DALI) with supplemental 2-wire control technology. Use with X5 power feed.

Power Tray: Code-gauge, die-formed steel, pre-paint white enamel finish; secured by quarter-turn fasteners for easy access to wiring. Holds ballasts, sock- ets, and wiring. Accepts ballasts up to 1.25” (3.18cm) wide by 1.20” (3.05cm) high. Power Feeds: Standard 18/3 power feed is rated for 10 amps. X4 power feed

is 18/4 and is rated for 7 amps. Observe amperage limitations and provide addi- tional Intermediate Power Cables, as required. When providing an additional power feed, the through wiring from the previous module must be disconnected from the cannon plug and capped.

Dual Switching: Use DS option for separate switching of the lamp rows. DS includes a 4th through wire. Use X4 power feed.

Factory installed ballast disconnect allows the ballast to be disconnected from and reconnected to incoming power under load without turning the entire circuit off.

Finish

Powder-coated, baked enamel, white or aluminum, as specified.

Mounting

Cable suspension is on 48” (121.92cm) and 96” (243.94cm) centers and consists of

a4 1/2” (11.43cm) diameter canopy finished white enamel and a 1/16” (0.16cm) diameter stainless steel aircraft cable adjustable up to 36” (91.44cm).

Labels

UL, cUL and I.B.E.W.

Ordering Instructions

Individual Fixtures:

1.Order one MODULE.

2.Order one POWER FEED END SET

Continuous Rows:

1.Order the appropriate number of MODULES for the complete run.

2.Order one POWER FEED END SET.

3.Order one INTERMEDIATE CABLE SET per MODULE minus one.

4.For runs that exceed amperage limits, order the appropriate number of CABLE/CORD SETs.

Job Information

Type:

Job Name:

Cat. No.:

Lamp(s):

Notes:

"JSQPSU3PBE'BMM3JWFS."t t'BY

We reserve the right to change details of design, materials and finish.

XXXMJHIUPMJFSDPN½1IJMJQT(SPVQt &

Philips F7000-17 specifications Features for Suspended Modules, Electrical, Finish, Mounting

Models: F7000-17