ENGLISH
HQ 564/563
Philishave
Cool Skin
Instructions for use
Opening for shaving emulsion
Cool Skin shaving heads
Release button shaving unit
Pump button
Cartridge compartment cover
Pilot light
ON/OFF button
Release button of cartridge compartment
Introduction
Cool Skin is a new shaving system by Philishave. The shaver has a special compartment for cartridges containing Nivea for Men moisturising shaving emulsion. This emulsion is applied to the skin during shaving. The Nivea for Men shaving emulsion prepares the skin and beard for the shave, ensuring that the shaver moves smoothly over your face and makes perfect contact with the skin. You will enjoy an unexpectedly close and comfortable shave and your skin will feel soft and fresh afterwards.
After shaving, you can clean the appliance by simply rinsing it under a hot tap.
Important
Allow your skin at least two weeks to become accustomed to the Philishave shaving system. Do not press the shaver too hard against the skin while shaving!
With this shaving system, you can shave when your skin is either wet or dry. The Nivea for Men shaving emulsion has an immediately moisturising effect on the skin.
Remove the cartridge and clean the shaver if you are not going to use the appliance for more than one week.
To obtain the best shaving results, it is necessary to follow the instructions in the ‘Cleaning and maintenance’ section.
Charging the shaver
Important: only leave the shaver to charge in a dry place!
First put the plug in the appliance and then put the Powerplug in the socket. The Powerplug has an automatic voltage selector and is suitable for mains voltages ranging from 100 to 240 Volts. The pilot light near the ON/OFF button will go on. It will take the appliance approximately 8 hours to recharge completely. A fully recharged shaver has a shaving time of approximately 30 minutes. The shaver has been equipped with a ‘battery low’ indication: the pilot light will light up when the battery is running low.
About the built-in battery
The shaver has been equipped with a
2
1
Inserting the cartridge
The cartridges with moisturising Nivea for Men shaving emulsion are available in boxes containing five cartridges and one plastic connector. Do not throw the connector away; you will need it for all five cartridges!
Use only Philishave Nivea for Men Cool Skin cartridges (HQ 150).
Inserting the first cartridge
■Take one cartridge from the box. Take the connector (supplied in the same box) out of its bag and push it into the cartridge until it seats with a click.
■Push the release slide downwards and remove the cover from the cartridge compartment.
■Slide the cartridge with inserted connector into the shaver. Replace the cover and close it.
Replacing an empty cartridge
■Push the release slide downwards and remove the cover from the cartridge compartment. Remove the empty cartridge and pull out the connector.
Note: do not throw the connector away!
■Insert the connector into a new cartridge. It has been properly inserted when it seats with a click.
■Slide the new cartridge with the connector into the shaver. Replace the cover and close it.
About the cartridge
The Nivea for Men shaving emulsion in this cartridge will keep when it is stored at a temperature between 0°C and +40°C.
Shaving
Switch on the shaver by pressing the ON/OFF button.
Hold the shaver against the skin.
■Press the yellow pump button to apply Nivea for
Men shaving emulsion to the skin. When sufficient shaving emulsion has been released, start moving the shaving heads rapidly over your skin, making both straight and circular movements.
The shaver is suitable for use in the shower.
Grooming sideburns and moustaches
Trimmer
The shaver has a separate trimmer for grooming sideburns and moustaches.
Fitting the trimmer onto the shaver
Switch off the shaver.
Clean the shaver before you assemble the trimmer.
■ Press the release button and pull the shaving unit off the shaver.
■ Fit the trimmer onto the shaver.
Removing the trimmer
Press the release button and remove the trimmer.
4222 001 83073
