Electronic Display Guide

Troubleshooting Guide

Care of your steriliser Guarantee

Steriliser plugged in and ready for mode selection

BEEP

BEEP

Ready for Mode 1 selection

Ready for Mode 2 selection

BEEP

BEEP

Mode 1 sterilisation in progress – indicated

Mode 2 sterilisation in progress – indicated by a

by a beep and rotating ‘0’

beep and three ascending and descending bars

Numerical countdown indicates sterilisation almost complete (Mode 1 only)

Steriliser will not work

 

Check that the mains lead is connected to the steriliser

 

 

 

as well as plugged into the mains. Check fuse in plug.

 

 

 

Excessive steam

 

Parts incorrectly loaded. Refer to instructions

escaping from

 

on page 4 or 5.

under the lid

 

 

 

 

 

Sterilising cycle

 

The steriliser is loaded with only a few items – light loads

takes too long

 

will take longer to cycle.

 

 

 

 

Flashing

 

 

Insufficient water has been placed in the steriliser. Switch

lower

BEEP

 

off, remove water, (take care if the steriliser body is hot)

and side

 

and replace with 90ml of water for use with Mode 1 OR

 

 

bars, and beep

 

200ml of water for use with Mode 2. Restart the unit.

 

 

 

 

Flashing

 

 

An excessive amount of water has been placed in the

top and

BEEP

 

steriliser. Switch off, remove water, (take care if the

side bars,

 

 

steriliser body is hot) and replace with 90ml of water for

and beep

 

 

use with Mode 1 OR 200ml of water for use with Mode 2.

 

 

 

Restart the unit.

 

 

 

 

Using pre-boiled or filtered water in your iQ24 Steriliser can reduce limescale build up. You should de-scale your steriliser every four weeks, or as often as needed in hard water areas, to ensure it continues to work 100% effectively. Under no circumstances should anything other than citric acid or vinegar be used as it may cause irreparable damage. Avoid contact with eyes as this may cause irritation. Keep out of the reach of children.

EITHER:

1.Mix one sachet of citric acid (10gms) with 200ml of water*. Pour into the empty steriliser. Do not put lid on.

Activate Mode 1 and leave for 1-2 minutes. Unplug and leave to stand for 30 minutes. Drain and rinse the inside of the steriliser. Then in Mode 1, run a full sterilising cycle empty with the lid on, using exactly 90ml of water. Drain and wipe dry.

OR:

Philips AVENT guarantees that should the iQ24 Electronic Steam Steriliser become faulty during twelve months from the date of purchase it will be replaced free of charge during this time. Please return it to the retailer where it was purchased. Please keep your receipt as proof of purchase, together with a note of when and where purchased. For the guarantee to be valid, please note:

The iQ24 Steriliser must be used according to the instructions in this booklet and connected to a suitable electricity supply.

The claim must not be a result of accident, misuse, dirt, neglect or fair wear and tear.

This Guarantee does not affect your statutory rights.

Key to product base label

BEEP

X 5

Sterilisation complete – indicated by 5 beeps and three flashing bars

– items will remain sterile for up to 6 hours provided the lid is not opened

Up to 6 hours sterile

Up to 4 hours sterile

Up to 2 hours sterile

time remaining

time remaining

time remaining

 

 

 

WARNINGS

• Ensure the steriliser is placed on a firm

level surface when in use.

• When in use, the steriliser contains

boiling water and steam escapes from

the vent in the lid.

• Never place items on top of the steriliser.

• Take care when opening as steam

can burn.

• During the sterilising cycle the lid and

the steriliser body are very hot.

• Never use the steriliser without water.

• Do not use bleach or chemical sterilising

solutions/tablets in your steam steriliser

or on products to be sterilised.

• Do not use abrasive, anti-bacterial

materials or scourers to clean the

steriliser.

• Do not use softened water in the

steriliser.

• The lead supplied must not be used on

any other appliance and no other lead

should be used with the iQ24 Steriliser.

• Failure to follow de-scaling instructions

2.Pour 100ml vinegar mixed with 200ml cold water into the steriliser. Allow to stand in the unit until any limescale has dissolved. Drain and rinse the inside of the steriliser thoroughly. Wipe dry.

*Citric Acid is available from most chemists

avoid contact with eyes as this may cause irritation. Keep out of reach of children.

FOR INDOOR USE ONLY

EUROPEAN STANDARD

DISPOSE OF THROUGH SEPARATE COLLECTION ROUTE FOR WASTE ELECTRICAL EQUIPMENT

BEEP

Mode 1 cycle (6 hours)

Completion of Mode 2 cycle (24 hours) – indicated by a long beep and a flashing ‘0’

BEEP

Water level too high. See ‘Troubleshooting’ on page 7

BEEP

Water level too low. See ‘Troubleshooting’ on page 7

• Always keep out of reach of children.

Never open the unit during the 6

minute sterilising cycle. Items are not

sterile if the 6 minute sterilising cycle

is interrupted.

• To completely stop the steriliser at any

time during a cycle, press and hold the

control button for 2 seconds to return

to selection mode or, unplug at the mains.

• Always disconnect the lead from the

back of the steriliser before pouring

away water and/or rinsing.

• Always unplug from the mains supply

when not in use.

• The power supply must be removed

from the unit for it to be completely

switched off.

• Never immerse the steriliser in water.

may cause irreparable damage.

• There are no serviceable parts inside the

iQ24 Steriliser. Do not attempt to open,

service or repair the iQ24 Steriliser

yourself.

• CAUTION: This appliance is intended

for use by responsible persons, keep

out of the reach of small children and

the infirm.

• This appliance is not intended for use

by persons including children with

reduced physical, sensory or mental

capabilities, or lack of experience or

knowledge, unless they have been given

supervision or instruction concerning use

of the appliance by a person responsible

for their safety.

• Children should be supervised to ensure

that they do not play with the appliance.

For our complete catalogue of mother and baby care products and breastfeeding video or DVD

GB: Call FREE on 0800 289 064

GB ONLY (9am–4.30pm Mon-Fri)

IRL: Call FREE on 1800 509 021

IRL ONLY (9am–4.30pm Mon-Fri)

AU: 1 300 364 474

(Australia National)

AVENT Ltd, Suffolk, CO10 7QS, England www(AVENT .Ltdphilipsis a member.com/AVENTf the Philips Group)

Philips of Holland. All logos brands and product names are trademarks or registered

trademarks of their respective holders and are hereby recognised as such.

iQ24

Electronic Steam Steriliser

6

7

42133 5435 060 #2 (10/07)

Page 1
Image 1
Philips iQ24 manual Lower, Off, remove water, take care if the steriliser body is hot, Level surface when in use, Can burn

iQ24 specifications

The Philips iQ24 is an innovative healthcare solution designed to enhance patient comfort and diagnostics in modern medical environments. This advanced device integrates cutting-edge technology with user-friendly features, making it a vital tool for healthcare professionals.

One of the main highlights of the iQ24 is its high-definition imaging capability. This device utilizes advanced imaging technologies that provide clear, detailed visuals, allowing for accurate diagnosis at the first point of care. With enhanced resolution and contrast, clinicians can quickly identify conditions, leading to faster treatment decisions.

The iQ24 incorporates various imaging modalities, including ultrasound and digital radiography. These technologies ensure that healthcare providers have access to a comprehensive diagnostic toolkit, streamlining the process of patient assessment while minimizing the need for multiple devices. The flexibility of the iQ24 means that it can be adapted for various medical applications, from obstetrics to musculoskeletal imaging.

One notable feature is its intuitive user interface, designed to facilitate ease of use even for those less experienced with imaging technology. The touchscreen controls and customizable settings enable clinicians to focus more on patient care rather than navigating complex menus. This user-centric design improves workflow efficiency and enhances the overall healthcare experience.

Another significant characteristic of the Philips iQ24 is its portability. Lightweight and compact, it is engineered for use in various clinical settings, from emergency rooms to outpatient facilities. This versatility ensures that high-quality imaging is accessible whenever needed, thereby improving patient outcomes.

Additionally, the iQ24 emphasizes patient safety and comfort. With its low radiation exposure during imaging, it aligns with modern standards for minimizing health risks associated with diagnostic procedures. The device also features ergonomic design elements that improve patient comfort during examinations.

Overall, the Philips iQ24 represents a significant leap forward in medical imaging technology. Its combination of high-definition imaging, user-friendly interface, portability, and patient safety features make it an essential instrument in modern healthcare delivery. As the demands of healthcare continue to evolve, devices like the iQ24 will play a crucial role in meeting those needs while providing exceptional patient care.