Section
02Operating this unit
| Section |
Operating this unit | 02 |
This unit is equipped with | # You can also perform the same operation on |
SLA (source level adjustment)
SLA (Source Level Adjustment) lets you adjust the volume level of each source to prevent radical changes in volume when switching between sources.
This setting allows you to switch your source to USB/ iPod automatically.
1 Press M.C. to turn the plug and play function on |
or off. |
ON – When a USB storage device/iPod is con- |
mination. You can select a desired color from | other colors. | English |
the color list. | 7 Press M.C. and hold until CUSTOM ap- | |
|
pears.
!Settings are based on the FM volume level, which remains unchanged.
!The AM volume level can also be adjusted with this function.
!When selecting FM as the source, you cannot
switch to SLA.
1Press M.C. to display the setting mode.
2Turn M.C. to adjust the source volume. Adjustment range: +4 to
3Press M.C. to confirm the selection.
Initial Settings
1Press S (SRC/OFF) and hold until the unit turns off.
2Press M.C. and hold until function name appears in the display.
3Turn M.C. to select the initial setting. After selecting, perform the following proce- dures to set the initial setting.
CLOCK SET (setting the clock)
nected, depending on the type of device, the |
source is automatically switched to USB/iPod |
when you turn on the engine. If you disconnect |
your USB storage device/iPod, this unit’s source |
is turned off. |
OFF – When a USB storage device/iPod is con- |
nected, the source is not switched to USB/iPod |
automatically. Please change the source to USB/ |
iPod manually. |
SW CONTROL (rear output and subwoofer setting)
The rear speaker leads output and RCA output can be used for
Initially,
1 | Press M.C. to display the setting mode. |
2 | Turn M.C. to change the output and press to se- |
| lect. |
| |
3 | Turn M.C. to change the setting. |
| |
| PREOUT: |
| ! Even if you change this setting, there is no |
| output unless you turn the subwoofer output |
| on (refer to SUBWOOFER1 (subwoofer on/off |
Direct selection from the illumination color list
1Press M.C. to display the main menu.
2Turn M.C. to change the menu option and press to select ILLUMI.
3Turn M.C. to select the illumination color.
You can select one option from the following list.
!30 preset colors (WHITE to ROSE)
!SCAN (cycle through all colors)
!CUSTOM (customized illumination color)
4Press M.C. to confirm the selection.
Notes
!When SCAN is selected, the illuminated color automatically cycles through the 30 preset colors.
!When CUSTOM is selected, the customized color saved is selected.
Using an AUX source
1Insert the stereo mini plug into the AUX input jack.
2Press S (SRC/OFF) to select AUX as the source.
Note
AUX cannot be selected unless the auxiliary setting is turned on. For more details, refer to AUX (auxiliary input) on the previous page.
Turning the clock display on or off
%Press to turn the clock display on or
off.
# The clock display disappears temporarily
when you perform other operations, but the clock display appears again after 25 seconds.
1Press M.C. to display the setting mode.
2Press M.C. to select the segment of the clock dis- play you wish to set.
3Turn M.C. to adjust the clock.
AUX (auxiliary input)
Activate this setting when using an auxiliary device connected to this unit.
1Press M.C. to turn AUX on or off.
USB (plug and play)
setting) on the previous page). |
! If you change this setting, subwoofer output |
in the audio menu will return to the factory |
settings. |
DEMO (demo display setting)
1Press M.C. to turn the demo display on or off.
SCROLL (scroll mode setting)
When ever scroll is set to ON, recorded text information scrolls continuously in the display. Set to OFF if you prefer the information to scroll just once.
1Press M.C. to turn the ever scroll on or off.
Customizing the illumination color
1 | Press M.C. to display the main menu. |
2 | Turn M.C. to change the menu option |
and press to select ILLUMI. | |
3 | Turn M.C. to select the preset color or |
CUSTOM illumination color. | |
# You cannot create a custom illumination color | |
when SCAN is selected. | |
4 | Press M.C. and hold until the customiz- |
ing illumination color setting appears in | |
the display. | |
5 | Press M.C. to select the primary color. |
R |
Selecting the illumination color
(Function of
6 Turn M.C. to adjust the brightness level. |
Adjustment range: 0 to 60 |
# You cannot select a level below 10 for all three |
of R (red), G (green), and B (blue) at the same |
time. |
12 | En | En | 13 |