Pioneer DEH-4400HD, DEH-44HD 9

Operating this unit

Section

Audio adjustments		Loudness compensates for deficiencies in the low-
1 Press M.C. to display the main menu.		frequency and high-frequency ranges at low vol-
1 Press M.C. to display the main menu.		ume.
		ume.
2 Turn M.C. to change the menu option		1 Press M.C. to select the desired setting.
2 Turn M.C. to change the menu option		OFF (off)—LOW(low)—HI (high)
and press to select AUDIO.		OFF (off)—LOW(low)—HI (high)
3 Turn M.C. to select the audio function.		SUB.W (subwoofer on/off setting)
3 Turn M.C. to select the audio function.		This unit is equipped with a subwoofer output
After selecting, perform the following proce-		This unit is equipped with a subwoofer output
dures to set the audio function.		which can be turned on or off.
		1 Press M.C. to select the desired setting.
FAD/BAL (fader/balance adjustment)		NOR (normal phase)—REV (reverse phase)—
FAD/BAL (fader/balance adjustment)		OFF (subwoofer off)
		OFF (subwoofer off)

SLA (source level adjustment)

SLA (Source level adjustment) lets you adjust the volume level of each source to prevent radical changes in volume when switching between sour- ces.

!Settings are based on the FM volume level, which remains unchanged.

!The AM volume level can also be adjusted with this function.

!When selecting FM as the source, you cannot switch to SLA.

1 Press M.C. to display the setting mode.

This setting allows you to switch your source to USB/iPod automatically.

1 Press M.C. to turn the plug and play function

on or off.

ON – When a USB storage device/iPod is con-

nected, depending on the type of device, the

source is automatically switched to USB/iPod

when you turn on the engine. If you disconnect

your USB storage device/iPod, this unit’s

source is turned off.

OFF – When a USB storage device/iPod is con-

nected, the source is not switched to USB/

English

1Press M.C. to display the setting mode.

2Press M.C. to cycle between fader (front/rear) and balance (left/right).

3Turn M.C. to adjust speaker balance.

!When the rear output and RCA output setting are SW, you cannot adjust front/rear speaker balance. Refer to REAR-SP (rear output setting) on this page. Refer to PREOUT (preout setting) on this page.

PRESET EQ (equalizer recall)

1Press M.C. to display the setting mode.

2Turn M.C. to select the equalizer.

DYNAMIC—VOCAL—NATURAL—CUSTOM

—FLAT—POWERFUL

3Press M.C. to confirm the selection.

TONE CTRL (equalizer adjustment)

!Adjusted equalizer curve settings are stored in

CUSTOM.

1Press M.C. to display the setting mode.

2Press M.C. to select BASS (bass)/MID (mid)/ TREBLE (treble).

3Turn M.C. to adjust the level. Adjustment range: +6 to –6

LOUD (loudness)

SUB.W CTRL (subwoofer adjustment)

The cut-off frequency and output level can be adjusted when the subwoofer output is on.

Only frequencies lower than those in the selected range are outputted from the subwoofer.

!When you select OFF in SUB.W, you cannot se-

lect this function. For details, refer to SUB.W (subwoofer on/off setting) on this page.

1Press M.C. to display the setting mode.

2Press M.C. to cycle between the cut-off fre- quency and output level of the subwoofer. Cut-off frequency (Cut-off frequency display flashes.)—Output level (Output level display flashes.)

3Turn M.C. to select the desired setting. Cut-off frequency: 50HZ—63HZ—80HZ— 100HZ—125HZ

Output level: –24 to +6

2	Turn M.C. to adjust the source volume.
	Adjustment range: +4 to –4
3	Press M.C. to confirm the selection.

Initial settings

1Press and hold SRC/OFF until the unit turns off.

2Press M.C. and hold until function name appears in the display.

3Turn M.C. to select the initial setting. After selecting, perform the following proce- dures to set the initial setting.

CLOCK SET (setting the clock)

1Press M.C. to display the setting mode.

2Press M.C. to select the segment of the clock display you wish to set.

Hour—Minute

3Turn M.C. to adjust the clock.

AUX (auxiliary input)

Activate this setting when using an auxiliary device connected to this unit.

1Press M.C. to turn AUX on or off.

USB PNP (plug and play)

iPod automatically. Please change the source

to USB/iPod manually.

REAR-SP (rear output setting)

The rear speaker leads output can be used for full- range speaker or subwoofer connection.

If you switch to SW, you can connect a rear speaker lead directly to a subwoofer without using an auxiliary amp.

Initially, REAR-SP is set for rear full-range speaker connection (FUL).

1Press M.C. to select the desired setting.

FUL—SW

!Even if you change this setting, there will be no output if you select OFF in SUB.W (Refer to SUB.W (subwoofer on/off setting) on this page).

!If you change this setting, subwoofer out- put in the audio menu will return to the fac- tory settings.

PREOUT (preout setting)