Section

02Operating this unit

Operating this unit

Section

02

The cut-off frequency and output level can be adjusted when the subwoofer output is on.

Only frequencies lower than those in the selected range are outputted from the subwoofer.

1Press M.C. to display the setting mode.

2Press M.C. to cycle between the cut-off frequency and output level of the subwoofer.

Cut-off frequency (Cut-off frequency display flashes.)—Output level (Output level display flashes.)

3Turn M.C. to select the desired setting.

Cut-off frequency: 50HZ—63HZ—80HZ—100HZ

—125HZ

Output level: -24 to +6

SLA (source level adjustment)

SLA (Source Level Adjustment) lets you adjust the volume level of each source to prevent radical changes in volume when switching between sources.

!Settings are based on the FM volume level, which remains unchanged.

!The AM volume level can also be adjusted with this function.

!When selecting FM as the source, you cannot switch to SLA.

1Press M.C. to display the setting mode.

2Turn M.C. to adjust the source volume. Adjustment range: +4 to –4

3Press M.C. to confirm the selection.

Initial Settings

1Press and hold S (SRC/OFF) until the unit turns off.

2Press M.C. and hold until function name appears in the display.

3Turn M.C. to select the initial setting. After selecting, perform the following proce- dures to set the initial setting.

CLOCK SET (setting the clock)

1Press M.C. to display the setting mode.

2Press M.C. to select the segment of the clock dis- play you wish to set.

Hour—Minute

3Turn M.C. to adjust the clock.

AUX (auxiliary input)

12 En

Activate this setting when using an auxiliary device connected to this unit.

1Press M.C. to turn AUX on or off.

USB (plug and play)

This setting allows you to switch your source to USB/ iPod automatically.

1Press M.C. to turn the plug and play function on or off.

ON – When a USB storage device/iPod is con- nected, depending on the type of device, the source is automatically switched to USB/iPod when you turn on the engine. If you disconnect your USB storage device/iPod, this unit’s source is turned off.

OFF – When a USB storage device/iPod is con- nected, the source is not switched to USB/iPod automatically. Please change the source to USB/ iPod manually.

ILLUMI (illumination color select)

1Press M.C. to display the setting mode.

2Turn M.C. to select the desired setting. RED (red)—GREEN (green)

3Press M.C. to confirm the selection.

SW CONTROL (rear output and subwoofer setting)

The rear speaker leads output and RCA output can be used for full-range speaker or subwoofer connection. If you switch to REAR-SP :SW, you can connect a rear speaker lead directly to a subwoofer without using an auxiliary amp.

Initially, REAR-SP is set for rear full-range speaker connection (FUL).

1Press M.C. to display the setting mode.

2Turn M.C. to change the output and press to se- lect.

REAR-SP—PREOUT

3Turn M.C. to change the setting. REAR-SP: FUL—SW PREOUT: SW—REA

!Even if you change this setting, there will be no output unless you turn the subwoofer out- put on (refer to SUBWOOFER1 (subwoofer on/ off setting) on the previous page).

!If you change this setting, subwoofer output in the audio menu will return to the factory settings.

DEMO (demo display setting)

1Press M.C. to turn the demo display on or off.

SCROLL (scroll mode setting)

When ever scroll is set to ON, recorded text information scrolls continuously in the display. Set to OFF if you prefer the information to scroll just once.

1Press M.C. to turn the ever scroll on or off.

Using an AUX source

1Insert the stereo mini plug into the AUX input jack.

2Press S (SRC/OFF) to select AUX as the source.

Note

AUX cannot be selected unless the auxiliary setting is turned on. For more details, refer to AUX (auxiliary input) on the previous page.

Turning the clock display on or off

%Press to turn the clock display on or

off.

# The clock display disappears temporarily

when you perform other operations, but the clock display appears again after 25 seconds.

English

En 13