3 Move the crossfader F gradually towards the right.

While checking the sound output from the speakers, operate the cross- fader to substitute the sound of [CH-1] with the sound of [CH-2].

Mixing is completed once only the [CH-2] sound is being output from the speakers.

Using the filter function (filter section)

g

SOUND COLOR FILTER

12

LPF

HPF

LPF

HPF

hh

Each channel is equipped with a SOUND COLOR FILTER function by which filter effects can be achieved simply by turning a large control. The treble or bass sound can be removed by turning the

[SOUND COLOR FILTER] control H.

Turn the [CH-1] 1 or [CH-2] 2 [SOUND COLOR FILTER] control H.

The effect is applied to the sound and the indicator’s color changes. The effect type and indicator color differs according to the direction in which the [FILTER] control is turned, as shown on the table below.

Direction of

Description of effect

Indicator

rotation

 

 

 

Applies the effect of the

 

Left

treble sound fading out.

Red (flashing)

 

(LPF: low pass filter)

 

 

 

 

Center

—

Orange (lit)

 

 

 

 

Applies the effect of the bass

 

Right

sound fading out.

Green (flashing)

 

(HPF: high pass filter)

 

 

 

 

Selecting the crossfader’s curve characteristics (crossfader section)

CROSS FADER

THRU

j

—[THRU]: Choose this when you do not want to use the crossfader.

—[]: Set here for a curve that rises gradually.

—[]: Set here for a curve that rises steeply. (When the crossfader moves away from either the left or right edge, the sound is immedi- ately output from the opposite side.)

Starting playback of a Pioneer DJ player using the fader (fader start section)

FADER START

CH-1 CH-2

i

If you connect a Pioneer DJ player using a control cable (supplied with a DJ player), you can start playback of control other operations of the DJ player with the fader of this unit.

The fader start function can only be used when connected to a Pioneer DJ player.

Connect this unit and Pioneer DJ player beforehand. For instructions on connections, see Connecting the input/output terminals on page 7.

Mixing using the SOUND COLOR FILTER control

Prepare the unit in advance so that the sound of [CH-1] 1 is being output from the speakers. For instructions on preparation, see Outputting sound on page 11.

For instructions on monitoring the sound, see Monitoring the sound over headphones (headphones section) on page 13.

1 Operate the crossfader and [CH-2] 2.

Operate as described in steps 2 to 6 under Mixing using the channel faders on page 11.

2Turn the [CH-2] 2 [SOUND COLOR FILTER] control H fully clockwise.

3Move the [CH-2] 2 channel fader E away from you.

4While turning the [CH-1] 1 [SOUND COLOR FILTER] control H counterclockwise from the center, turn the [CH-2] 2 [SOUND COLOR FILTER] control H towards the center.

While checking the sound output from the speakers, operate the

[SOUND COLOR FILTER] controls H and replace the [CH-1] and [CH-2] sound.

Move the [CH-1] 1 channel fader E towards the front. Mixing is completed once only the sound of [CH-2] is output from the speakers.

To start playback using the channel faders

1Set [THRU, ,] (the crossfader curve selector switch) J to [THRU].

2Press the [CH-1] or [CH-2] button I in the fader start section.

Turn the fader start function on.

3Move the channel fader E to the very front.

4Set the cue on the DJ player.

The DJ player pauses playback at the cue point.

5 Move the channel fader E away from you.

Playback starts on the DJ player.

!If you set the channel fader back to the original position, the player instantaneously returns to the cue point already set and pauses playback (back cue).

12En