PART NAMES AND FUNCTIONS

Rear Panel

59

60

61

62

63

64

65

CONTRAST

BRIGHT

75

74

 

CH-2

L

SEND

L

RETURN

L

CH-1

MIC

 

 

R

R

R

 

R

L

 

 

 

CD

 

 

 

 

CD

 

 

 

 

MASTER 2

 

(MONO)

 

 

(MONO)

PHONO

 

 

66

R

L

PHONO

 

 

 

 

 

 

/ LINE

 

MASTER 1

 

/ LINE

 

 

 

 

 

 

 

 

 

 

 

R

L

 

 

PHONO

 

 

3 COLD

 

 

 

PHONO

 

 

 

 

 

 

1 GND

 

 

 

 

 

 

SIGNAL

LINE

 

 

 

 

 

SIGNAL

LINE

SESSION IN

 

GND

CH-2 PLAYER

 

 

 

 

GND

 

 

BOOTH/

R

2 HOT

L

CH-1 PLAYER

 

 

 

CONTROL

CONTROL

 

 

 

SESSION OUT

 

 

 

 

 

 

 

 

 

 

73 72

71

 

70

 

69

68 67

 

59CH-2 input jacks

CD

Connect to audio output from CH-2 CD player.

PHONO / LINE

Connect to audio output from CH-2 analog turntable, cassette deck or other line signal level component.

67 CH-1 PHONO/LINE selector switch

Use to set the input sensitivity at the CH-1 PHONO/LINE connectors. The [PHONO] position supports an MM type cartridge.

*When no analog turntable is used, set this switch to the [LINE] side.

60 External effector output jacks (SEND)

Connect to the input connectors of an external effector. When the top panel switches (MIC SEND, CH-1 SEND, and CH-2 SEND) are set to On, these jacks output the MIC, CH-1, and CH-2 signals to the external effector.

When using an effector with a monaural input, connect it to the L channel output only. The signal actually sent to the effector will represent a mix of L and R signals.

61Touch panel screen contrast control (CONTRAST)

Use to adjust the top panel’s touch panel contrast.

62External effector return jacks (RETURN)

Connect to the output connectors of the external effector. When using an effector with monaural output, connect only to the L channel input. The signal received from the effector will be input to both L and R channels.

63Touch panel backlight control (BRIGHT)

Use to adjust the top panel’s touch panel backlight luminance.

64CH-1 input jacks

CD

Connect to the audio output of the CH-1 CD player.

PHONO / LINE

Connect to audio output from CH-1 analog turntable, cassette deck or other line signal level component.

65Microphone input jack (MIC)

Connect to a microphone with XLR type or PHONE type plug. When applying effects to the microphone sound, set the top panel’s CH-1 input selector switch (MIC–PHONO 1/LINE 1– CD1) to the [MIC] position.

66 Session input jacks (SESSION IN)

When using multiple mixers simultaneously, connect the other mixer outputs to these jacks.

68 CH-1 signal ground (SIGNAL GND)

Connect to the CH-1 analog turntable’s ground wire. Note that this is not meant as a safety ground.

69 CH-1 PLAYER CONTROL jack

When a Pioneer DJ CD player is connected to the CH-1 CD jacks, a special control cord can be used to connect this jack to the player’s control jack, thus enabling the fader start function.

70 MASTER 1 jacks

XLR type balanced output. Connect to the power amplifier’s balanced input jacks.

71 CH-2 PLAYER CONTROL jack

When a Pioneer DJ CD player is connected to the CH-2 CD jacks, a special control cord used to connect this jack to the player’s control jack, thus enabling the fader start function.

72 CH-2 PHONO/LINE selector switch

Use to set the input sensitivity at the CH-2 PHONO/LINE connectors. The [PHONO] position supports an MM type cartridge.

*When no analog turntable is used, set this switch to the [LINE] side.

73 CH-2 signal ground (SIGNAL GND)

Connect to the CH-2 analog turntable’s ground wire. Note that this is not meant as a safety ground.

74 BOOTH/SESSION OUT jacks

Connector jacks for booth monitor output. When using this unit in tandem with another mixer, connect these jacks to the other mixer’s session input jacks.

75 MASTER 2 jacks

RCA type unbalanced output. Connect to the power amplifier’s unbalanced input jacks.

13

<DRB1349>