Installation
CAUTION
•Do not install in:
•Make sure that wires are not caught in the sliding mechanism of the seats, resulting in a
•Confirm that no parts are behind the panel when drilling a hole for installation of the amplifier. Protect all cables and important equipment such as fuel lines, brake lines and electrical wiring from damage.
•Install tapping screws in such a way that the screw tip does not touch any wire. This is impor- tant to prevent wires from being cut by vibration of the car, which can result in fire.
•To prevent electric shock, do not install the ampli- fier in places where it might come in contact with liquids.
•To ensure proper installation, use the supplied parts in the manner specified. If any parts other than the supplied ones are used, they may damage internal parts of the amplifier, or they may become loose causing the amplifier to shut down.
To prevent malfunction
•To ensure proper heat dissipation of the amplifier, be sure of the following during installation.
•Do not install the amplifier near a door where it may get wet.
•Do not install the amplifier on unstable places such as the spare tire board.
•The best location for installation differs with the car model and installation location. Secure the amplifier at a sufficiently rigid location.
•Make temporary connections first and check that the amplifier and the system operate properly.
•After installing the amplifier, confirm that the spare tire, jack and tools can be easily removed.
Example of installation on the floor mat or on the chassis
1.Place the amplifier where it is to be
installed. Insert the supplied tapping screws (4 ⋅ 18 mm) into the screw holes. Push on the screws with a screwdriver so they make marks where the installation holes are to be located.
2.Drill 2.5 mm (1/8 inch) diameter holes at the point marked, and install the amplifier, either on the carpet or directly to the chassis.
Floor mat or chassis
Drill a 2.5 mm (1/8 inch) diameter hole
Specifications
GM-X362
Power source | 14.4 V DC (10.8 — 15.1 V allowable) |
Grounding system | Negative type |
Current consumption | 11.3 A (at continuous power, 4 Ω) |
Average current drawn* | 3.8 A (4 Ω for two channels) |
| 5.9 A (4 Ω for one channel) |
Fuse | 20 A |
Dimensions | 279 (W) ⋅ 61 (H) ⋅ 157 (D) mm |
| [11 (W) ⋅ |
Weight | 2.6 kg (5.7 lbs) (Leads for wiring not included) |
Maximum power output | 80 W ⋅ 2 / 200 W ⋅ 1 |
Continuous power output | 40 W ⋅ 2 (at 14.4 V, 4 Ω, 20 — 20,000 Hz, 0.08% THD) |
| 100 W ⋅ 1 (at 14.4 V, 4 Ω, 20 — 20,000 Hz, 0.8% THD) |
| 50 W ⋅ 2 (at 14.4 V, 2 Ω, 20 — 20,000 Hz, 0.8% THD) |
Load impedance | 4 Ω (2 — 8 Ω allowable) |
| (Bridge connection: 4 — 8 Ω allowable) |
Frequency response | 10 — 50,000 Hz (+0 dB, |
100 dB | |
Distortion | 0.008% (10 W, 1 kHz) |
Separation | 60 dB (1 kHz) |
Low pass filter | Cut off frequency: 80 Hz |
| Cut off slope: |
Maximum input level/impedance | RCA: 6.5 V/22 kΩ (0.4 — 6.5 V) |
| Speaker: 26 V/40 kΩ (1.6 — 26 V) |
Note:
•Specifications and the design are subject to possible modification without notice due to improvements.
*Average current drawn
•The average current drawn is nearly the maximum current drawn by this unit when an audio signal is input. Use this value when working out total current drawn by multiple power amplifiers.
GM-X262
Power source | 14.4 V DC (10.8 — 15.1 V allowable) |
Grounding system | Negative type |
Current consumption | 11.3 A (at continuous power, 4 Ω) |
Average current drawn* | 3.8 A (4 Ω for two channels) |
| 5.9 A (4 Ω for one channel) |
Fuse | 20 A |
Dimensions | 279 (W) ⋅ 61 (H) ⋅ 157 (D) mm |
| [11 (W) ⋅ |
Weight | 2.6 kg (5.7 lbs) (Leads for wiring not included) |
Maximum power output | 80 W ⋅ 2 / 200 W ⋅ 1 |
Continuous power output | 40 W ⋅ 2 (at 14.4 V, 4 Ω, 20 — 20,000 Hz, 0.08% THD) |
| 100 W ⋅ 1 (at 14.4 V, 4 Ω, 20 — 20,000 Hz, 0.8% THD) |
| 50 W ⋅ 2 (at 14.4 V, 2 Ω, 20 — 20,000 Hz, 0.8% THD) |
Load impedance | 4 Ω (2 — 8 Ω allowable) |
| (Bridge connection: 4 — 8 Ω allowable) |
Frequency response | 10 — 50,000 Hz (+0 dB, |
100 dB | |
Distortion | 0.008% (10 W, 1 kHz) |
Separation | 60 dB (1 kHz) |
Low pass filter | Cut off frequency: 80 Hz |
| Cut off slope: |
Maximum input level/impedance | RCA: 6.5 V/22 kΩ (0.4 — 6.5 V) |
| Speaker: 26 V/40 kΩ (1.6 — 26 V) |
Note:
•Specifications and the design are subject to possible modification without notice due to improvements.
*Average current drawn
•The average current drawn is nearly the maximum current drawn by this unit when an audio signal is input. Use this value when working out total current drawn by multiple power amplifiers.
