( Connections
Connecting the units
'H~~d'u'nW" .....
(sold'$eparately)
) (~ | E~ng~l_is_h) |
BluelWhite
Control signal is output through blue/white cable when Pioneer head unit is turned on, Connect it to the
(Tn~In_s_t_al_la_t_io_n~)
Connections
~Important
• | Use this unit in a vehicle of a |
| negative grounding. |
• | To prevent |
| malfunction, be sure to follow the directions |
(English)
• Before drilling any mounting holes always check | |
| behind where you want to drill the holes, Do not |
| drill into the gas line, brake line, electrical wiring or |
| other important parts. |
• | If this unit installed in the passenger compartment, |
| anchor it securely so it does not break free while |
| the vehicle is moving, and cause injury or an |
| accident. |
• | If this unit is installed under a front seat, make |
r
/
To Ip·BUSinput (blue)
3 m (9 ft. 10 in.)
. .
Antenna
3 m (9 ft. 10 in.)
Antenna cable (supplied)
antenna booster power supply terminal,
| below. |
- | Disconnect the negative terminal of the battery |
| before installation. |
- | Secure the wiring with cable clamps or adhesive |
| tape. To protect the wiring, wrap adhesive tape |
| arou nd them where they lie agai nst metal parts, |
- | Place all cables away from moving parts, such as |
| gear shift and seat rails. |
- | Place all cables away from hot places, such as |
| near the heater outlet. |
- | Do not pass the yellow cable through a hole into |
| the engine compartment to connect to a battery. |
- | Do not shorten any cables. |
- | Never cut the insulation of the power cable of |
| this unit in order to share the power to other |
| equipment. Current capacity of the cable is |
| limited, |
- Use a fuse of the rati ng prescri bed. | |
• | |
| connect connectors of the same color, |
• Place antenna cable as far away as possible from | |
| the other cables to prevent noise, |
• Black cable is ground. This cable and other | |
| product'sground cable (especially, |
| products such as power amp) must be wired |
| separately. Otherwise, fire or malfunction may |
| result if they are accidentally detached. |
sure it does not obstruct seat movement. Route |
all leads and cords carefully around the sliding |
mechanism so they do not caught or pinched in |
the mechanism and cause a |
Mounting with hook and loop fasteners
Thoroughly wipe off the surface before affixing the hook and loop fasteners.
•If the hook fasteners adhere to the car mat directly, you may install this unit without using the loop fasteners.
Mount this unit using the hook and loop fasteners.
Car antenna cable (form vehicle'santenna) Connect the car antenna cable to this unit's
Installing this unit
antenna input. It is not necessary to connect to head unit'santenna input.
~Important
Car mat or chassis
If you use this ur')itwith ~rlavigation system that can receive traffic information from thebuilt·in FM tuner, cOll.neCtthe car antenna cable to both this Unit ancLthe'na.vigationsystem with an antenna s'plitferorto a separate antenna.
Fuse (2 A) | Yellow |
| Connect to the constant |
| 12 V supply terminal. |
Black (chassis ground)
Connect to a clean.
•Check all connections and systems before final installation.
•Do not use unauthorized parts. The use of unauthorized parts may cause malfunctions.
•Consult with your dealer if installation requires drilling of holes or other modifications of the vehicle.
•Do not install this unit where:
-it may interfere with operation of the vehicle,
-it may cause injury to a passenger as a result of a sudden stop.
•When mounting this unit, make sure none of the leads are trapped between this unit and the surrounding metalwork or fittings.
•Do not mount this unit near the heater outlet, where it would be affected by heat, or near the doors, where rainwater might splash onto it.
