Planet Technology SGSW-2402 3.2 Web Pages, 3.3 Port Config

3.2 Web Pages

To access the Web-browser interface you must first enter the password. The default password is "admin" You will see the following screen comes out on the Web browser program:

Figure 3-1 : Password Screen

After the password is entered you will see the main menu screen.

Figure 3-2: The start up screen of SGSW-2402 Web Page

3.3 Port Config

This section allows you to have an easy access in configuring the ports of the management Switch. Notice that the “Link state” option indicates “Up”. This shows that the port is connected to the network. It can either be in “Up” (Connected) or “Down” (No connection) state.

Contents

10/100/1000Mbps Intelligent Stackable Switch Trademarks Disclaimer FCC Warning CE Mark Warning Revision TABLE OF CONTENTS Page 1. INTRODUCTION 1.1 Checklist 1.2 About the Switch 1.3Features 1.4Specification Page 2. HARDWARE DESCRIPTION 2.1 Front Panel 2.2 Rear Panel 2.3Hardware Installation 2.3.1 Connecting end node or hub or switch 2.3.2 Connecting to Network Backbone or Server 2.4 Terminal Setup 2.5 IP Configuration sys set ip sys set ip 192.168.0.2 255.255.255.0 3.WEB-BASEDMANAGEMENT 3.1 Configuration 3.2 Web Pages 3.3 Port Config Choose Port Speed/ Duplex ‘Auto’: ‘10Mbps HD’: ‘10Mpbs FD’: 3.4 VLAN Config Setup Procedures 3.5 Trunk config Port Trunking Setup Procedures 3.6 Advanced Configuration 3.7 STP Config 3.7.1 STP Port 3.7.2 STP Bridge Description of Parameters 3.8 IGMP 3.8.1 IGMP Management 3.8.2 Definition on IGMP v1.0 and 3.9 Stack Step 5: Step 6: Step 7: 3.10 SNMP 3.11 RMON Statistics 3.12 Port Security 3.12.1 Setting Up Procedures 3.12.2 Delete MAC Address For deleting individual MAC Address For deleting ALL MAC Addresses 3.13 Mirror Port 3.13.1 Using Mirror Port to Monitor Traffic 3.13.2 Setup Procedures 3.14 Aging Control Aging Control Configuration Procedures 3.15 Address Search 3.15.1 Host Searching Procedures 3.15.2 MAC Address Search MAC Address Search Procedures 3.16 System Tools 3.17 System Config 3.18 System Information 3.19 Change Password Changing password procedure 3.20 Firmware Upgrade Upgrade Firmware Procedure 3.21 Save & Reboot 3.21.1 Save 3.21.2 Backup Page 3.21.3 Restore 3.21.4 Clear and Reset 3.22 Message Windows 3.23 Reboot Switch 3.24 Logout NOT 4 CONSOLE INTERFACE 4.1 CONNECT TO PC 4.2 Logging on to the Switch “Help” SYS--SYSTEMMANAGEMENT COMMANDS LOGOUT--EXITMANAGEMENT COMMANDS PORT--PORTMANAGEMENT COMMANDS 4.2.1. sys--SystemManagement Commands 4.2.2 sys show info 4.2.3. sys show IP 4.2.4. sys show Ethernet address 4.2.5. sys set ip <IP Address> <Subnet Mask> <Default Gateway 4.2.6. sys set name "string 4.2.7. sys set contact "string 4.2.8. sys set location "string 4.2.9. sys set password 4.2.10. sys set link_info <on|off 4.2.11. sys reset system 4.2.12. sys reset config 4.2.13. sys save config 4.2.14. logout 4.2.15. port--PortManagement Commands 4.2.16. port show 4.2.17.port set enable <port number> [-h|-f] [-10|-100|-1000] [-A] 4.2.18.port set disable <port number 4.2.19. port set flw <port number> <on|off 4.2.20. port set bck <port number> <on|off 4.2.21.port set pri <port number> <-ppriority 4.2.22. port set vid <port number> <-vvid 4.2.23. vlan--VLANManagement Commands 4.2.24. vlan show 4.2.25. vlan build <vid> <-uuntags> <-ttags> <-ppriority 4.2.26. vlan delete <vid 4.2.27.vlan set pri <vid> <-ppriority 4.2.28. trunk--TRUNKManagement Commands 4.2.29. trunk show 4.2.30.trunk set <port1> [port2] [port3] [port4] 4.2.31. stp--STPManagement Commands 4.2.32. snmp--SNMPManagement Commands 4.2.33. stack--STACKManagement Commands APPENDIX A NETWORKING CONNECTION