Planet Technology WAP-1966 1.4Specification

Point-to-MultiPoint)

•Provide Windows-based configuration utility and Web Configuration

1.4Specification

Standard	IEEE 802.11b Compliant
Signal Type	DSSS (Direct Sequence Spread Spectrum)
Modulation	QPSK / BPSK / CCK / PBCC
Port	One 10/100BASE-TX
Antenna	1 x Dipole Antenna
Data Encryption	64 bit / 128 bit / 256bit WEP encryption

Frequency	2.4GHz - 2.4835GHz
Channel	11 Channels (US, Canada)
	13 Channels (Europe)
	14 Channels (Japan)
Data Rate	1/2/5.5/11/22Mbps, 22Mbps+4X
LED Indicators	Power, WLAN, LAN
Power Requirement	5V DC, 2.5A
Temperature	Operating :0 ~ 55 degree C
	Storage: -10 ~ 70 degree C
Humidity	Operating: 5 ~ 95%
	Storage: 0 ~ 95% Non-Condensing
Dimensions	196x120x31mm
Output Power	17dBm±1dBm
Antenna Gain	2dBi
Antenna Connector	Reversed Polarity SMA Male

- 2 -

Contents

WAP-1966 User’s Manual Copyright Federal Communication Commission Interference Statement FCC Caution: Federal Communication Commission (FCC) Radiation Exposure Statement R&TTE Compliance Statement Safety Revision TABLE OF CONTENTS Page Chapter 1 Introduction 1.1 Package Contents 1.2 System Requirements 1.3Features 1.4Specification Chapter 2 Hardware Installation Chapter 3 Configuring the Wireless Access Point 3.1 Configure through Web Browser 3.1.1 Wizard Step 2. Set the SSID and Channel Step 3. Set Encryption Step 4. Restart 3.1.2 Status: 3.1.3 Basic Settings: 3.1.4 IP Settings: 3.1.5 Advanced Settings: AP Mode: AP: AP Client Wireless Bridge Multiple Bridge 3.1.6 Security: Password: MAC Filters: 3.1.8 Tools: 3.2 Configure through 22M AP Utility 3.2.1 Install 22M AP Utility 3.2.2 22M AP Utility configuration 3.2.2.1 Link Information 3.2.2.2 AP Settings Basic Settings: ESSID Channel AP Name Mode Settings: Transmission Rates: Preamble Type: Beacon Interval: DTIM Interval: 3.2.2.3 IP Settings 3.2.2.4 WEP Settings 3.2.2.5 802.1x Settings Chapter 4 802.1X Authentication Setup 4.1 802.1X Infrastructure 4.2 RADIUS Server Setup 4.2.1 Required Services 4.2.2 Setup Procedure 7.Go to Start > Program > Administrative Tools > Certificate Authority Policy Setting new 9.Select “Certificate to Issue” Authenticated Session Properties Group Policy Page Finish Start > Run command Enter 20.Type “secedit/refreshpolicy machine_policy” to refresh policy Setting Internet Authentication Service Client New Client Client address Client-Vendor “Finish” Remote Access Policies 29.Select “New Remote Access Policy” Day-And-Time-Restriction Add Grant remote access permission 33.Click “Edit Profile” Page Internet Authentication Service (Local) Register Service in Active Directory Edit Page Define this policy setting Enabled Users “Apply” Dial-in Allow access Call-back 4.3 Authenticator Setup 4.4 Wireless Client Setup 4.4.1 EAP-MD5Authentication Data encryption (WEP enabled Network key MD-5 Challenge 4.4.2 EAP-TLSAuthentication user name password Request a certificate User Certificate request Submit Install this certificate Yes Wireless Adapter Setup Page 6.Select “The key is provided for me automatically” option “OK” 8.Click “Authentication” tab Enable network access control using IEEE Smart Card or other Certificate Page Chapter 5 Application 5.1 Access Point mode 5.2 Wireless AP Client mode 5.3 Wireless Bridge mode 5.4 Multiple Bridge mode 5.5 Repeater mode Chapter 6 Troubleshooting What is Roaming