Manuals / Brands / Computer Equipment / Network Router / Planet Technology / Computer Equipment / Network Router

Planet Technology WAP-4000 Chapter 2 Hardware Installation, RJ-45, Connect, WAP-4000, cable to, WAP-4000, Assemble the antennas to, Locate an optimum location for the

1 57

Download 57 pages, 2.86 Mb

Chapter 2 Hardware Installation

Before you proceed with the installation, it is necessary that you have enough information about the WAP-4000.

1.Locate an optimum location for the WAP-4000. The best place for your WAP-4000 is usually at the center of your wireless network, with line of sight to all of your mobile stations.

2.Assemble the antennas to WAP-4000.Try to place them to a position that can best cover your wireless network. The antenna’s position will enhance the receiving sensitivity.

3.Connect RJ-45 cable to WAP-4000.Connect this WAP-4000 to your LAN switch/hub or a single PC.

4.Plug in power adapter and connect to power source. After power on, WAP-4000 will start to operate.

Note: ONLY use the power adapter supplied with the WAP-4000. Otherwise, the product may be damaged.

If you want to reset your WAP-4000 to default settings, press the Reset button 5 second. And then wait for 10 seconds for WAP-4000 to reboot.

- 4 -

Contents

WAP-4000 User’s Manual Copyright Federal Communication Commission Interference Statement FCC Caution: Federal Communication Commission (FCC) Radiation Exposure Statement R&TTE Compliance Statement Safety Revision TABLE OF CONTENTS Page Chapter 1 Introduction 1.1 Package Contents 1.2 System Requirements 1.3Features 1.4 Specification 1.5 Wireless Performance Chapter 2 Hardware Installation Chapter 3 Configuring the Wireless Access Point 3.1 Configure through Web Browser 3.1.1 Wizard Step 3. Set Encryption Step 4. Restart 3.1.2 Status: 3.1.3 Basic Settings: 3.1.4 IP Settings: IP address Subnet Mask Gateway DHCP DNS 3.1.5 Advanced Settings: 3.1.6 Security: Password: MAC Filters: Enable/Disable: Encryption Key: RADIUS Server 1: RADIUS Server 2: 3.1.8 Tools: 3.2 Configure through 54M AP Utility 3.2.1 Install 54M AP Utility Page 3.2.2 54M AP Utility configuration 3.2.2.1 Link Information 3.2.2.2 AP Settings Advance setting: Transmission Rates: 11G Only Mode: 3.2.2.3 IP Settings 3.2.2.4 WEP Settings 3.2.2.5 802.1x Settings Chapter 4 802.1X Authentication Setup 4.1 802.1X Infrastructure 4.2 RADIUS Server Setup 4.2.1 Required Services 4.2.2 Setup Procedure 7.Go to Start > Program > Administrative Tools > Certificate Authority Policy Setting new 9.Select “Certificate to Issue” Authenticated Session Properties Group Policy Page Finish Start > Run command Enter 20.Type “secedit/refreshpolicy machine_policy” to refresh policy Setting Internet Authentication Service Client New Client Client address Client-Vendor “Finish” Remote Access Policies 29.Select “New Remote Access Policy” Day-And-Time-Restriction Add Grant remote access permission 33.Click “Edit Profile” Page Internet Authentication Service (Local) Register Service in Active Directory Edit Page Define this policy setting Enabled Users “Apply” Dial-in Allow access Call-back 4.3 Authenticator Setup 4.4 Wireless Client Setup 4.4.1 EAP-MD5Authentication Data encryption (WEP enabled Network key MD-5 Challenge 4.4.2 EAP-TLSAuthentication User Certificate request Submit Install this certificate Yes Wireless Adapter Setup 6.Select “The key is provided for me automatically” option “OK” 8.Click “Authentication” tab Enable network access control using IEEE Smart Card or other Certificate Page Chapter 5 Application 5.1 Access Point mode 5.2 Wireless AP Client mode 5.3 Wireless Bridge mode 5.4 Multiple Bridge mode Chapter 6 Troubleshooting