![OPTION #2](/images/new-backgrounds/11087/110879x1.webp)
OPTION #2
This method can be used with electronics that include a “SUB OUT” feature (Figure 4, previous page). It is not recommended for use with RM6200 or RM6600 Systems.
Connect a single RCA cable from the “SUB OUT” of your electronics to the LFE input of the subwoofer. This input bypasses the sub- woofer’s variable low pass filter and relies on the filter built into your electronics. If your “SUB OUT” is an unfiltered signal (check your owner’s manual), use either left or right “Line Level Input,” to use the low pass crossover in the subwoofer.
When using option #2, it is necessary to adjust the settings of your electronics as follows: Front speakers = large or small depending on their output capabilities; Subwoofer = “ON”.
OPTION #3
This method is for use with electronics featur- ing a “PRE OUT” – and may be used as a sec- ondary hook up method for use with RM6200 or RM6600 Systems. Connect the left and right preamp output from your electronics to the left and right LINE LEVEL input of the subwoofer. This may require use of RCA “Y” cables (not supplied) to hookup both the subwoofer and your electronics (PSW250, PSW350, PSW450). When using option #3, it is necessary to adjust the settings on your electronics as follows: Front speakers = LARGE Subwoofer = “OFF” or “NO”.
OPTION #2 | FIGURE 4 |
|
|
|
|
|
SUB OUT HOOKUP |
|
|
|
|
|
|
PSW350 AND |
|
|
|
|
|
|
PSW450 ONLY |
|
|
|
|
|
|
This method is for |
|
|
|
|
|
|
use with electronics |
|
|
|
|
|
|
that include a “sub | FRONT |
|
|
|
| FRONT |
out” feature. |
| RECEIVER | ||||
CHANNEL |
| CHANNEL | ||||
|
|
|
|
| ||
| FRONT |
|
| |||
|
|
| R | L | + |
|
| - + |
| - | - |
| |
|
|
|
|
| - + | |
|
|
| SPEAKER LEVEL OUTPUT | |||
| RCA CABLE |
| + R | - | - | L + |
|
|
|
|
|
| |
|
|
| + R | - | - | L + |
| R | L | SPEAKER LEVEL INPUT | |||
| Line |
|
| LFE | ||
|
|
| Level |
|
|
|
|
|
| Input |
|
|
|
7 F o r c u s t o m e r s e r v i c e c a l l 8 0 0 - 3 7 7 - 7 6 5 5 |
|
|
|
|
|
OPTION #3
PRE OUT
HOOKUP
This method is for use with electonic components featuring a
FIGURE 5
FRONT | POWER AMPLIFIER | FRONT | ||||||
CHANNEL |
|
|
| FRONT |
|
| CHANNEL | |
INPUT |
|
|
|
|
| |||
L | R |
|
| R | L |
|
|
|
- + |
|
| - | + | - | + |
|
|
|
|
|
|
|
|
| - + | |
| ||||||||
|
|
|
|
| ||||
|
|
|
| L | R |
|
| Y CABLES |
|
|
|
|
|
|
|
| |
|
|
| SPEAKER LEVEL OUTPUT |
| ||||
|
|
| + | R | - | - | L + |
|
|
|
| + R | - | - | L + | RCA CABLES | |
| R | L | SPEAKER LEVEL INPUT |
| ||||
| Line |
| LFE |
|
|
| ||
|
|
| Level |
|
|
|
|
|
|
|
| Input |
|
|
|
|
|
F o r m o r e i n f o r m a t i o n v i s i t o u r w e b s i t e a t h t t p : / / w w w. p o l k a u d i o . c o m 8 |