Polycom 1725-36097-001, 6000 System, MOG400, RCC400, RCO400, RCU100, RCU200, RCU201, SCA408, SCA416, SCA516, SCC408, SCC416, SCD408, SCD416, SCE408, SCE416, SCF4089, SCF416, SCI408, SCI416, SCJ408, SCJ416, SCK408, SCK416, SCL408, SCL416, SCM408, SCM416, SCN408, SCN416, SCO408, SCO416, SCS416, SCT416, SCX416 Status LED Codes

SpectraLink 6100 MCU: Installation and Operation: SpectraLink 6000 System

PN: 1725-36097-001_J.doc

Certain four-wire telephones (such as MERLIN LEGEND) use a

different connector on the phone than on the back of the MCU.

Therefore you may need phone cord or an adapter to perform these

tests.

Status LED Codes

STATUS LEDs

1 2 3 4 5 Description Action

Random

Cycling

The SpectraLink 6100 MCU is

powering up. Initialization to

follow.

This is not an error and should change to

another code after a minute.

5 SpectraLink 6100 MCU is

initalizing.

Code number will change when finished.

1, 2, 3, or 4 MCU identification number. Indicates normal operation when it is on steady.

If the same LED is lit on more

than one MCU:

Check the IPC connections.

If the LED is flashing and the

ERROR light is on:

There is a problem with the MCU indicated by

the flashing box ID.

Contents

Main Patent Information Copyright Notice Notice Contact Information About this Guide Polycom Model Numbers Related Documents Customer Support Icons and Conventions Contents 0 1 2 3 5 6 7 8 Page Page Installation Overview Installation Steps and Responsibilities SpectraLink 6000 System Overview System Operation Master Control Unit (MCU) Base Stations SpectraLink 6000 Wireless Telephones SpectraLink 6100 OAI Gateway System Capacity Base Station Capacity Individual MCU Capacity Maximum System Capacity The Front Panel of the SpectraLink 6100 MCU Site Preparation Required Materials Provided by Customer Determine Location of MCU Run Cable for System Run Cables to Base Station Locations Wire specifications Pull Cable Terminate Cable at Base Station Locations Prepare Demarc Blocks Multiple power pairs Dedicated line for diagnostic modem Two-wire analog or digital interface Four-wire digital interface Four-wire Digital Connection Install Demarc Blocks Assign and Program Ports Connect Cables from Base Stations and Phone Lines to Demarc Blocks Two-wire analog or digital demarc block The demarc block for the two-wire analog or digital interface should be wired as follows. Two-wire Connector Four-wire digital demarc block Four-wire Connector A Four-wire Connector B Install SpectraLink 6000 System Survey Site Check Components Page Install MCUs Mount MCUs to wall Grounding instructions Safety Warning Connect MCU to demarc blocks Connect multi-unit systems Page Connect power Set switch interface type Page Page Install Base Stations Mount Base Stations on dropped tile ceilings Mount Base Stations on finished ceilings Install Outdoor Base Stations Wire and connect outdoor Base Stations Page Connect and Register Handsets Set Up Diagnostic Modem Register Handsets Unregister Handsets Program Handset Features Test Handsets Site Certification Page System Administration Troubleshoot Error Codes Troubleshoot Handset Features Status LED Codes The following STATUS LEDs are displayed in combination with the Handset Status Indicator Messages Replace a Handset Delete old handset Register new handset Replace an MCU Clear configuration on replacement MCU Connect the replacement MCU Replace a Base Station Handset Planning Worksheet MCU ID: _________ Page Base Station Location Worksheet Page Technical Parameters Select Alternate Spread Spectrum Sequence Change Companding Safety Notices Page Index A B C D M P Q R S

Polycom Status LED Codes

Models: 1725-36097-001 6000 System MOG400 RCC400 RCO400 RCU100 RCU200 RCU201 SCA408 SCA416 SCA516 SCC408 SCC416 SCD408 SCD416 SCE408 SCE416 SCF4089 SCF416 SCI408 SCI416 SCJ408 SCJ416 SCK408 SCK416 SCL408 SCL416 SCM408 SCM416 SCN408 SCN416 SCO408 SCO416 SCS416 SCT416 SCX416

Certain four-wire telephones (such as MERLIN LEGEND) use a

different connector on the phone than on the back of the MCU.

Therefore you may need phone cord or an adapter to perform these

tests.