SERVICE AND ADJUSTMENTS

TRANSAXLE GEAR SHIFT LEVER NEUTRAL ADJUSTMENT (See Fig. 26)

The transaxle should be in neutral when the gear shift lever is in neutral (N) (lock gate) position. The adjustment is preset at the factory; however, if adjustment is needed, proceed as follows:

•Make sure transaxle is in neutral (N).

NOTE: When the tractor rear wheels move freely, the transaxle is in neutral.

•Loosen adjustment bolt in front of the right rear wheel.

•Position the gear shift lever in the neutral (N) position.

•Tighten adjustment bolt securely.

NOTE: If additional clearance is needed to get to adjustment bolt, move mower deck height to the lowest position.

GEARSHIFT LEVER

NEUTRAL

LOCK GATE

ADJUSTMENT

BOLT

FIG. 26

TO ADJUST STEERING WHEEL ALIGNMENT

If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble per instructions in the Assembly section of this manual.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not adjustable on your tractor. If damage has occurred to affect the front wheel toe- in or camber, contact your nearest authorized service center/department.

TO REMOVE WHEEL FOR REPAIRS (See Fig. 27)

•Block up axle securely.

•Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).

•Repair tire and reassemble.

•On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

•Replace washers and snap retaining ring securely in axle groove.

•Replace axle cover.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

WASHERS

RETAINING

RING

AXLE COVER

SQUARE KEY (REAR WHEEL ONLY)

FIG. 27

TO START ENGINE WITH A WEAK BATTERY (See Fig. 28)

CAUTION: Lead-acid batteries generate explosive gases. Keep sparks, flame and smoking materials away from bat- teries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the CUSTOMER RESPON- SIBILITIES section of this manual).

If “jumper cables” are used for emergency starting, follow this procedure:

IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT NEGATIVE GROUNDED SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT NEGATIVE GROUNDED SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES.

TO ATTACH JUMPER CABLES -

•Connect each end of the RED cable to the POSITIVE (+) terminal of each battery, taking care not to short against chassis.

•Connect one end of the BLACK cable to the NEGATIVE (-) terminal of fully charged battery.

•Connect the other end of the BLACK cable to a good CHASSIS GROUND, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER -

•BLACK cable first from chassis and then from the fully charged battery.

•RED cable last from both batteries.

21

Page 20 Page 22
Page 21
Image 21
Poulan 178085 owner manual Transaxle Gear Shift Lever Neutral Adjustment See Fig, To Adjust Steering Wheel Alignment
Page 20 Page 22

178085 specifications

The Poulan 178085 is a highly regarded chainsaw known for its durability, efficiency, and ease of use. Designed primarily for homeowners and light-duty commercial use, this model stands out for its impressive balance between power and user-friendliness. Whether tackling tree trimming, firewood cutting, or general yard maintenance, the Poulan 178085 delivers reliable performance.

One of the key features of the Poulan 178085 is its robust engine. Equipped with a 40cc gas-powered engine, this chainsaw generates enough power to handle various cutting tasks with ease. The engine is designed to be fuel-efficient, allowing users to maximize runtime while minimizing fuel consumption and emissions. Additionally, its easy-start technology ensures that the chainsaw can be fired up with minimal effort, making it accessible even for those who may be new to using chainsaws.

The chainsaw boasts a 16-inch bar, which provides an optimal cutting length for most home and garden applications. This ideal size strikes a balance between maneuverability and cutting capability, allowing users to cut through branches and logs efficiently. The low-kickback design of the bar and chain improves safety during operation, making it less likely for the saw to kick back unexpectedly.

Another notable characteristic of the Poulan 178085 is its lightweight construction. Weighing in at only about 10 pounds, this chainsaw is easy to handle and reduces user fatigue during extended periods of use. Its comfortable grip and well-placed controls enhance the overall user experience, allowing for smoother operation and better precision while cutting.

To further enhance safety, the Poulan 178085 includes a chain brake feature that stops the chain in the event of kickback. This critical safety mechanism is a vital addition for both novice and experienced users, providing peace of mind while operating the saw.

In terms of maintenance, the Poulan 178085 features an automatic oiling system that keeps the chain lubricated during cutting, ensuring a longer lifespan for both the chain and bar. This feature reduces the need for manual lubrication, making it more convenient for users.

In summary, the Poulan 178085 is a versatile and reliable chainsaw equipped with a powerful engine, a well-designed bar, and a range of safety features. Its lightweight design and user-friendly technologies make it an excellent choice for anyone looking to manage their yard work effectively and safely. Whether you are a seasoned professional or a DIY enthusiast, the Poulan 178085 is a tool that meets the demands of modern cutting and trimming tasks.
Top Page Image Contents