CUSTOMER RESPONSIBILITIES

BATTERY

Your tractor has a battery charging system which is suffi- cient for normal use. However, periodic charging of the battery with an automotive charger will extend its life.

Keep battery and terminals clean.

Keep battery bolts tight.

Keep small vent holes open.

Recharge at 6-10 amperes for 1 hour.

NOTE: The original equipment battery on your tractor is maintenance free. Do not attempt to open or remove caps or covers. Adding or checking level of electrolyte is not necessary.

TO CLEAN BATTERY AND TERMINALS

Corrosion and dirt on the battery and terminals can cause the battery to “leak” power.

Disconnect BLACK battery cable first then RED battery cable and remove battery from tractor.

Rinse the battery with plain water and dry.

Clean terminals and battery cable ends with wire brush until bright.

Coat terminals with grease or petroleum jelly.

Reinstall battery (See “REPLACING BATTERY” in the SERVICE AND ADJUSTMENTS section of this manual).

V-BELTS

Check V-belts for deterioration and wear after 100 hours of operation and replace if necessary. The belts are not adjustable. Replace belts if they begin to slip from wear.

TRANSAXLE COOLING

Keep transaxle free from build-up of dirt and chaff which can restrict cooling.

ENGINE

LUBRICATION

Only use high quality detergent oil rated with API service classification SF-SJ. Select the oil’s SAE viscosity grade according to your expected operating temperature.

SAE VISCOSITY GRADES

 

 

 

 

 

 

 

 

 

 

SAE 30

 

 

 

 

 

 

5W-30

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

F

-20

0

 

 

30 32 40

 

60

80

100

C

-30

-20

-10

0

10

20

30

40

TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE

FIG. 10

NOTE: Although multi-viscosity oils (5W30, 10W30 etc.) improve starting in cold weather, these multi-viscosity oils will result in increased oil consumption when used above 32°F. Check your engine oil level more frequently to avoid possible engine damage from running low on oil.

Change the oil after every 25 hours of operation or at least once a year if the tractor is not used for 25 hours in one year.

Check the crankcase oil level before starting the engine and after each eight (8) hours of operation. Tighten oil fill cap/ dipstick securely each time you check the oil level.

TO CHANGE ENGINE OIL (See Fig. 11)

Determine temperature range expected before oil change. All oil must meet API service classification SF-SJ.

Be sure tractor is on level surface.

Oil will drain more freely when warm.

Catch oil in a suitable container.

Remove oil fill cap/dipstick. Be careful not to allow dirt to enter the engine when changing oil.

Remove yellow cap from end of drain valve and install the drain tube onto the fitting.

 

OIL DRAIN VALVE

CLOSED

 

AND

 

LOCKED

 

POSITION

 

 

DRAIN

YELLOW

TUBE

CAP

 

FIG. 11

Unlock drain valve by pushing inward and turning coun- terclockwise.

To open, pull out on the drain valve.

After oil has drained completely, close and lock the drain valve by pushing inward and turning clockwise until the pin is in the locked position as shown.

Remove the drain tube and replace the cap onto to the bottom fitting of the drain valve.

Refill engine with oil through oil fill dipstick tube. Pour slowly. Do not overfill. For approximate capacity see “PRODUCT SPECIFICATIONS” section of this manual.

Use gauge on oil fill cap/dipstick for checking level. Be sure dipstick cap is tightened securely for accurate reading. Keep oil at “FULL” line on dipstick.

16

Page 16
Image 16
Poulan 182946 manual Engine, Battery, Belts, Transaxle Cooling, Lubrication

182946 specifications

The Poulan 182946 is a power-packed chainsaw designed for both amateur woodworkers and professional landscapers alike. Built with robust features and cutting-edge technologies, this chainsaw offers an impressive balance of performance, efficiency, and ease of use, making it an ideal choice for a wide range of cutting tasks.

One of the most notable features of the Poulan 182946 is its powerful engine, which delivers high speed and torque necessary for cutting through tough materials. The chainsaw is equipped with a 42cc engine that provides an excellent blend of power and lightweight design, allowing users to tackle tasks with less fatigue. The inclusion of an automatic oiling system ensures that the chain is always properly lubricated for smooth operation, thereby extending the life of the chainsaw and maintaining optimal cutting performance.

The cutting capacity of the Poulan 182946 is further enhanced by a 16-inch bar and chain. This size strikes an ideal balance for residential projects like trimming branches, cutting firewood, or clearing small trees, without making the tool cumbersome or difficult to handle. Its low kickback design offers added safety, which is essential for beginners and those less experienced with power tools.

In terms of technological features, the Poulan 182946 incorporates a tool-less chain tensioning system. This allows users to make quick adjustments to the chain without the use of additional tools, significantly speeding up the setup process. The easy-start system minimizes the effort required to start the engine, ensuring that users can get to work without unwanted delays.

Furthermore, the chainsaw is designed with user comfort in mind. Its ergonomic handle allows for a secure grip, reducing vibration and enhancing control during operation. The compact design also contributes to a balanced feel in hand, facilitating prolonged use without discomfort.

The Poulan 182946 is not just a powerful tool; it is a reliable partner for all cutting tasks. Whether you are a seasoned professional or a DIY enthusiast, this chainsaw promises to deliver exceptional performance, reliability, and user-friendly features that enhance your cutting experience. Ultimately, the Poulan 182946 stands as a testament to Poulan's commitment to creating quality outdoor power equipment that meets the needs of today's users.