To Replace Headlight Bulb, Interlocks and Relays

SERVICE AND ADJUSTMENTS

•Lift seat pan to raised position.

•Disconnect BLACK battery cable ﬁrst then RED battery cable and carefully remove battery from tractor.

•Install new battery with terminals in same position as old battery.

•First connect RED battery cable to positive (+) terminal with hex bolt and keps nut as shown. Tighten securely. Slide terminal cover over terminal.

•Connect BLACK grounding cable to negative (-) ter- minal with remaining hex bolt and keps nut. Tighten securely.

SEAT PAN

	FIG. 27
TERMINAL	KEPS NUT	HEX
COVER		BOLT
POSITIVE (RED) CABLE		NEGATIVE (BLACK) CABLE

FIG. 28

TO REPLACE HEADLIGHT BULB

•Raise hood.

•Pull bulb holder out of the hole in the backside of the grill.

•Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill.

•Close hood.

INTERLOCKS AND RELAYS

Loose or damaged wiring may cause your tractor to run poorly, stop running, or prevent it from starting.

•Check wiring. See electrical wiring diagram in the Repair Parts section.

TO REPLACE FUSE

Replace with 20 amp automotive-type plug-in fuse. The fuse holder is located behind the dash.

TO REMOVE HOOD AND GRILL ASSEMBLY (See Fig. 29)

•Raise hood.

•Unsnap headlight wire connector.

•Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor.

•To replace, reverse above procedure.

HOOD

HEADLIGHT

WIRE

CONNECTOR

01536

FIG. 29

TO ADJUST THROTTLE CONTROL CABLE (See Fig. 30)

The throttle control has been preset at the factory and adjustment should not be necessary. Check adjustment as described below before loosening cable. If adjustment is necessary, proceed as follows:

•With engine not running, move throttle control lever from slow to choke position. Slowly move lever from choke to fast position.

•Check that holes “A” in governor control lever and hole in governor plate line-up. If holes “A” are not aligned, loosen clamp screw and move throttle cable until holes are aligned. Tighten clamp screw securely.

GOVERNOR CONTROL LEVER
		GOVERNOR CONTROL PLATE
HOLES “A”	CLAMP	THROTTLE
	SCREW	CABLE
		CABLE

FIG. 30

TO ADJUST CARBURETOR

The carburetor has been preset at the factory and adjustment should not be necessary. However, minor adjustment may be required to compensate for differences in fuel, temperature, altitude or load. If the carburetor does need adjustment, see engine manual.

High speed stop is factory adjusted. Do not adjust - dam- age may result.

IMPORTANT:NEVERTAMPERWITHTHEENGINEGOVERNOR, WHICH IS FACTORY SET FOR PROPER ENGINE SPEED. OVERSPEEDING THE ENGINE ABOVE THE FACTORY HIGH SPEED SETTING CAN BE DANGEROUS. IF YOU THINK THE ENGINE-GOVERNED HIGH SPEED NEEDS ADJUSTING, CONTACTYOUR NEAREST AUTHORIZED SERVICE CENTER/ DEPARTMENT, WHICH HAS PROPER EQUIPMENT AND EXPERIENCE TO MAKE ANY NECESSARY ADJUSTMENTS.

187301 specifications

The Poulan 187301 is a specialized lawn care tool designed for both professional landscapers and enthusiastic homeowners. Known for its versatility and performance, this robust piece of equipment stands out in the crowded market of leaf blowers and lawn maintenance devices.

One of the main features of the Poulan 187301 is its powerful engine. Equipped with a reliable two-stroke engine, it delivers excellent airflow at an impressive speed, making it easy to clear leaves, debris, and grass clippings from lawns and driveways. The engine not only ensures top-tier performance but also maintains an environmentally friendly profile thanks to its efficient fuel consumption.

Weight and ergonomics play a crucial role in the usability of the Poulan 187301. Weighing slightly less than many competitors, this leaf blower is designed for extended use without causing undue strain on the operator. The comfortable handle provides a secure grip, allowing users to maneuver it easily around gardens and larger spaces.

The Poulan 187301 boasts an airspeed capacity that can reach up to 200 miles per hour, which translates into swift and effective clearing of debris. The adjustable speed settings allow users to tailor the airflow according to their specific needs, ensuring optimal performance whether dealing with wet leaves or light dust and sand.

Another key characteristic of this model is its ease of start. The Poulan 187301 incorporates advanced starting technology that minimizes the effort required to get the blower running, an essential feature for those who want to avoid frustration when starting up their equipment.

In terms of design, the Poulan 187301 is built to last, with a durable construction that can withstand the rigors of outdoor use. With minimal maintenance required, owners can expect a long lifespan from this equipment, making it a valuable investment.

Moreover, the Poulan 187301 is considered a quieter alternative compared to many other models on the market. This reduced noise level is particularly appealing for residential areas where excessive noise can be an annoyance to neighbors.

In conclusion, the Poulan 187301 combines power, efficiency, and user-friendly features, making it an excellent choice for those seeking to enhance their lawn care routine. With its advanced technologies and focus on user experience, this tool is set to meet the diverse needs of both homeowners and professionals alike.

Poulan 187301 manual To Replace Headlight Bulb, Interlocks and Relays, To Replace Fuse

Models: 187301