Manuals / Poulan / Lawn and Garden / Tiller

Poulan 188904 TO REPLACE GROUND DRIVE BELT See Figs. 22 and, GROUND DRIVE BELT ADJUSTMENT See Fig

Models: 188904

1 28

Download 28 pages 24.51 Kb

Page 15

TO REPLACE GROUND DRIVE BELT (See Figs. 22 and 23)

SERVICE AND ADJUSTMENTS

TO REPLACE GROUND DRIVE BELT (See Figs. 22 and 23)

•Remove belt guard as described in “TO REMOVE BELT GUARD”.

•Remove old belt by slipping off engine pulley ﬁrst then remove from transmission pulley.

•Place new belt in groove of transmission pulley and into engine pulley. BELT MUST BE IN GROOVE ON TOP OF IDLER PULLEY. NOTE POSITION OF BELT TO GUIDES.

•Check belt adjustment as described below.

•Replace belt guard.

•Reposition wheel and replace clevis pin and hairpin clip.

GROUND DRIVE BELT ADJUSTMENT (See Fig. 23)

For proper belt tension, the extension spring should have about 5/8 inch (16 mm) stretch when drive control bar is in “ENGAGED” position. This tension can be attained as follows:

•Loosen cable clip screw securing the drive control cable.

•Slide cable forward for less tension and rearward for more tension until about 5/8 inch (16 mm) stretch is obtained while the drive control bar is engaged.

•Tighten cable clip screw securely.

CABLE CLIP SCREW

ENGINE

PULLEYDRIVE CONTROL CABLE

LESS

TENSION

		MORE
5/8"		TENSION

EXTENSION

IDLERSPRING

PULLEYTRANSMISSION

PULLEY

FIG. 23

15

Image 15

Poulan 188904 TO REPLACE GROUND DRIVE BELT See Figs. 22 and, GROUND DRIVE BELT ADJUSTMENT See Fig, Service And Adjustments

Contents

OWNERS MANUAL MODELPRRT65D IMPORTANT MANUALTRAINING SAFETY RULESSafe Operation Practices for Walk-Behind Powered Rotary Tillers MAINTENANCE AND STORAGETABLE OF CONTENTS PRODUCT SPECIFICATIONSCUSTOMER RESPONSIBILITIES OPERATOR’S POSITION See Fig ASSEMBLYTOOLS REQUIRED FOR ASSEMBLY CONTENTS OF HARDWARE PACKINSTALL HANDLE See Figs. 3, 4, and UNPACKING CARTON See FigASSEMBLY CHECK TIRE PRESSURE ATTACH CLUTCH CABLE See FigCONNECT SHIFT ROD See Fig REMOVE TILLER FROM CRATEKNOW YOUR TILLER READ THIS OWNERS MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TILLERMEETS ANSI SAFETY REQUIREMENTS OPERATIONFORWARD - WHEELS ONLY/TINES STOPPED HOW TO USE YOUR TILLERSTOPPING See Fig TINE OPERATION - WITH WHEEL DRIVECHECK ENGINE OIL LEVEL See Fig OUTER SIDE SHIELDS See FigTO TRANSPORT BEFORE STARTING ENGINEOPERATION TINE SHEAR PINSTILLING HINTS CULTIVATINGGENERAL RECOMMENDATIONS MAINTENANCEMAINTENANCE SCHEDULE LUBRICATION CHARTLUBRICATION ENGINEAIR FILTER See Fig MAINTENANCESPARK PLUG CLEANINGCOOLING SYSTEM See Fig MUFFLERTIRE CARE SERVICE AND ADJUSTMENTSTO ADJUST HANDLE HEIGHT See Fig TILLERGROUND DRIVE BELT ADJUSTMENT See Fig TO REPLACE GROUND DRIVE BELT See Figs. 22 andSERVICE AND ADJUSTMENTS TINE REPLACEMENT See Figs. 24, 25, and SERVICE AND ADJUSTMENTStine13 ENGINE TO ADJUST THROTTLE CONTROL CABLE See FigTO ADJUST CARBURETOR SERVICE AND ADJUSTMENTSENGINE OIL STORAGEOTHER FUEL SYSTEMTROUBLESHOOTING POINTS REPAIR PARTS HANDLE ASSEMBLYTILLER - - MODEL NUMBER PRRT65D mainframeleft17 MAINFRAME, LEFT SIDEREPAIR PARTS TILLER - - MODEL NUMBER PRRT65DMAINFRAME, RIGHT SIDE REPAIR PARTSTILLER - - MODEL NUMBER PRRT65D transmission19.5b REPAIR PARTSTILLER - - MODEL NUMBER PRRT65D TRANSMISSIONtineshield16in TINE SHIELDREPAIR PARTS TILLER - - MODEL NUMBER PRRT65Dtineipb1 TINE ASSEMBLYREPAIR PARTS TILLER - - MODEL NUMBER PRRT65DDECALS REPAIR PARTSTILLER - - MODEL NUMBER PRRT65D LIMITED WARRANTY FOR SERVICE OR REPLACEMENT PARTS PARTS AND SERVICE