To Level Mower Housing, Belt Installation

SERVICE AND ADJUSTMENTS

TO LEVEL MOWER HOUSING

Adjust the mower while tractor is parked on level ground or driveway. Make sure tires are properly inﬂated (See “PRODUCT SPECIFICATIONS” section of this manual). If tires are over or underinﬂated, you will not properly adjust your mower.

SIDE-TO-SIDE ADJUSTMENT (See Figs. 14 and 15)

•Raise mower to its highest position.

•At the midpoint of both sides of mower, measure height from bottom edge of mower to ground. Distance “A” on both sides of mower should be the same or within 1/4" of each other.

•If adjustment is necessary, make adjustment on one side of mower only.

•To raise one side of mower, tighten lift link adjustment nut on that side.

•To lower one side of mower, loosen lift link adjustment nut on that side.

NOTE: Each full turn of adjustment nut will change mower height about 1/8".

•Recheck measurements after adjusting.

BOTTOM EDGE		BOTTOM EDGE
OF MOWER TO		OF MOWER TO
GROUND		GROUND
A	GROUND LINE	A

FIG. 14

SUSPENSION ARM

LIFT LINK

ADJUSTMENT NUT

FIG. 15

FRONT-TO-BACK ADJUSTMENT (See Figs. 16 and 17)

IMPORTANT: DECK MUST BE LEVEL SIDE-TO-SIDE. IF THE FOLLOWING FRONT-TO-BACK ADJUSTMENT IS NECESSARY, BE SURE TO ADJUST BOTH FRONT LINKS EQUALLY SO MOWER WILL STAY LEVEL SIDE-TO-SIDE.

To obtain the best cutting results, the mower housing should be adjusted so that the front is approximately 1/8" to 1/2" lower than the rear when the mower is in its high- est position.

Check adjustment on right side of tractor. Measure distance “D” directly in front and behind the mandrel at bottom edge of mower housing as shown.

•Before making any necessary adjustments, check that both front links are equal in length.

•If links are not equal in length, adjust one link to same length as other link.

•To lower front of mower loosen nut “E” on both front links an equal number of turns.

•When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nuts “F” against trunnion on both front links.

•To raise front of mower, loosen nut “F” from trunnion on both front links. Tighten nut “E” on both front links an equal number of turns. The two front links must remain equal in length.

•When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nut “F” against trunnion on both front links.

•Recheck side-to-side adjustment.

MANDREL

“D”

FIG. 16

BOTH FRONT LINKS MUST BE EQUAL IN LENGTH

NUT “F”

NUT “E”

TRUNNION

FRONT LINKS

FIG. 17

TO REPLACE MOWER BLADE DRIVE BELT (See Fig. 18)

The mower blade drive belt may be replaced without tools. Park the tractor on level surface. Engage parking brake.

BELT REMOVAL -

•Place attachment clutch in “DISENGAGED” position.

•Move attachment lift lever forward to lower mower to its lowest position.

•Roll belt off engine pulley.

•Disconnect R.H.suspension arm from rear deck bracket by removing retainer spring.

•Work belt off both mandrel pulleys and idler pulleys.

•Pull belt away from mower.

BELT INSTALLATION -

•Work new belt around both mandrel pulleys and idler pulleys.

•Install new belt into engine pulley groove. Reconnect R.H. suspension arm and secure with re- tainer spring.

•Make sure belt is in all pulley grooves and inside all

20belt guides.

194598 specifications

The Poulan 194598 is a noteworthy entry in the realm of outdoor power equipment, particularly tailored for lawn care. This product, recognized for its reliability and functionality, is primarily a chainsaw that caters to both amateur gardeners and professionals alike. As part of Poulan’s commitment to innovation and quality, the 194598 model embodies several features and technologies designed to enhance the user experience.

At its core, the Poulan 194598 boasts a robust engine that provides ample power for cutting through various types of wood, whether it's trimming branches or felling small trees. This chainsaw typically comes equipped with a powerful two-cycle engine, delivering streamlined performance while ensuring efficiency. The engine is designed for easy starting, minimizing the hassle often encountered with starting similar devices.

One of the standout features of the Poulan 194598 is its lightweight design. Weighing significantly less than many competing models, this chainsaw allows for extended use without leading to user fatigue. The ergonomic handle contributes to a comfortable grip, which is essential during prolonged operations. This thoughtful design is a hallmark of Poulan products, reflecting their understanding of user ergonomics.

In terms of safety, the Poulan 194598 is equipped with several essential safety features. These include a chain brake, which can be activated in instances of kickback, significantly reducing the risk of injury. Additionally, an integrated chain tensioning system allows users to make adjustments quickly and easily, promoting safe and efficient operation.

Another notable attribute is the chainsaw's low vibration technology. This feature not only enhances user comfort but also contributes to a more stable performance. Less vibration translates to better control and precision during cutting tasks, making the Poulan 194598 an appealing option for those who value accuracy in their work.

Maintenance is also straightforward with the Poulan 194598, as it typically offers easy access to the air filter and spark plug, allowing for routine upkeep to be performed without excessive effort. This aspect appeals to both casual users and more serious professionals who appreciate devices that require less downtime.

In summary, the Poulan 194598 is a versatile, user-friendly chainsaw that combines power, safety, and comfort. Its thoughtful design, augmented by technologies that minimize vibration and enhance safety, make it an excellent choice for anyone looking to tackle outdoor cutting tasks efficiently and reliably. With its robust features and characteristics, the Poulan 194598 stands as a commendable tool for both homeowners and landscape professionals.

Poulan 194598 manual To Level Mower Housing, Belt Installation

Models: 194598