To Replace Mower Blade Drive Belt See Fig

SERVICE AND ADJUSTMENTS

SIDE-TO-SIDE ADJUSTMENT (See Figs. 15 and 16)

•Raise mower to its highest position.

•At the midpoint of both sides of mower, measure height from bottom edge of mower to ground. Distance “A” on both sides of mower should be the same or within 1/4" of each other.

•If adjustment is necessary, make adjustment on one side of mower only.

•To raise one side of mower, tighten lift link adjustment nut on that side.

•To lower one side of mower, loosen lift link adjustment nut on that side.

NOTE: Three full turns of adjustment nut will change mower height about 1/8".

•Recheck measurements after adjusting.

BOTTOM EDGE OF		BOTTOM EDGE
MOWER		OF MOWER
TO GROUND		TO GROUND
“A”	GROUND LINE	“A”

FIG. 15

SUSPENSION ARM

LIFT LINK ADJUSTMENT NUT

FIG. 16

FRONT-TO-BACK ADJUSTMENT (See Figs. 17 and 18)

IMPORTANT: DECK MUST BE LEVEL SIDE-TO-SIDE. IF THE FOLLOWING FRONT-TO-BACK ADJUSTMENT IS NECESSARY, BE SURE TO ADJUST BOTH FRONT LINKS EQUALLY SO MOWER WILL STAY LEVEL SIDE-TO-SIDE.

To obtain the best cutting results, the mower housing should be adjusted so that the front is approximately 1/8" to 1/2" lower than the rear when the mower is in its high- est position.

Check adjustment on right side of tractor. Measure distance “D” directly in front and behind the mandrel at bottom edge of mower housing as shown.

•Before making any necessary adjustments, check that both front links are equal in length.

•If links are not equal in length, adjust one link to same length as other link.

•To lower front of mower loosen nut “E” on both front links an equal number of turns.

•When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nuts “F” against trunnion on both front links.

•To raise front of mower, loosen nut “F” from trunnion on both front links. Tighten nut “E” on both front links an equal number of turns. The two front links must remain equal in length.

•When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nut “F” against trunnion on both front links.

•Recheck side-to-side adjustment.

MANDREL

"D"

FIG. 17

BOTH FRONT LINKS MUST BE EQUAL IN LENGTH

NUT "F"

NUT "E"

TRUNNION

FRONT LINKS

FIG. 18

TO REPLACE MOWER BLADE DRIVE BELT (See Fig. 19)

The mower blade drive belt may be replaced without tools. Park the tractor on level surface. Engage parking brake.

BELT REMOVAL -

•Remove mower from tractor (See “TO REMOVE MOWER” in this section of this manual).

•Work belt off both mandrel pulleys and idler pulleys.

•Pull belt away from mower.

BELT INSTALLATION -

•Install new belt in reverse order of removal.

•Make sure belt is in all pulley grooves and inside all belt guides.

•Install mower in reverse order of removal instruc- tions.

MANDREL	IDLER
PULLEY	PULLEYS
MANDREL
PULLEY

FIG. 19

197022 specifications

The Poulan 197022 is a robust and reliable chainsaw designed for both homeowners and professionals alike. Known for its powerful performance and innovative features, the 197022 stands out in the competitive market of outdoor tools. This model is particularly favored for its versatility, making it suitable for a variety of tasks ranging from trimming branches to felling trees.

One of the main features of the Poulan 197022 is its powerful engine. Equipped with a 50cc two-stroke engine, this chainsaw delivers impressive power for demanding cutting jobs. The engine's design optimizes fuel efficiency, ensuring that users can complete tasks without frequent refueling. This characteristic is essential for large-scale projects, where time and fuel consumption are critical considerations.

The Poulan 197022 also boasts an 18-inch cutting bar, which provides an ideal balance between maneuverability and cutting capacity. This length allows for efficient cutting through a wide range of materials while maintaining ease of use for the operator. The chainsaw’s Oregon chain contributes to smooth and effective cutting performance, ensuring that users achieve clean cuts with minimal effort.

In terms of technology, the Poulan 197022 features an advanced air filtration system that ensures prolonged engine life by keeping dust and debris from entering the engine. This system is crucial for maintaining optimal performance and reducing maintenance needs. Additionally, the chainsaw incorporates an automatic oiling system that delivers consistent lubrication to the blade, further enhancing durability and performance.

Safety is a priority with the Poulan 197022. It includes several safety features such as a chain brake that activates instantly to prevent accidents in case of kickback. The anti-vibration technology used in this model significantly reduces operator fatigue by minimizing the vibrations felt during operation. This feature is particularly beneficial for users who may spend extended periods cutting wood.

Overall, the Poulan 197022 is designed for ease of use and user comfort. Its lightweight design and ergonomic handle ensure that it is accessible for users of all experience levels. Whether for light yard work or heavy-duty cutting, the Poulan 197022 is a standout choice, combining power, efficiency, and safety in one dependable chainsaw.

Poulan 197022 manual To Replace Mower Blade Drive Belt See Fig, Belt Removal, Belt Installation

Models: 197022