Manuals / Poulan / Lawn and Garden / Tiller

Poulan 403701 INSERT CABLE CLIP See Fig, CONNECT SHIFT ROD See Fig, Remove Tiller From Crate

Models: 96092001200 403701

1 28

Download 28 pages 14.63 Kb

Page 6

INSERT CABLE CLIP (See Fig. 6)

ASSEMBLY

INSERT CABLE CLIP (See Fig. 6)

•Insert plastic cable clip into hole on the back of handle column. Push cables into clip.

HANDLE COLUMN

CABLES

CABLE CLIP

FIG. 6

CONNECT SHIFT ROD (See Fig. 7)

•Insert end of shift rod farthest from bend into hole of shift lever indicator.

•Insert hairpin clip through hole of shift rod to secure with bend of clip on right side.

REMOVE TILLER FROM CRATE

•Adjust handle assemby to lowest position. Be sure lock lever is tightened securely.

•Make sure shift lever indicator is in “N” (neutral) position (See Fig. 7)

•Tilt tiller forward by lifting handle. Separate cardboard cover from leveling shield.

•Rotate tiller handle to the right and pull tiller out of carton.

	ATTACH THIS END	SHIFT ROD
	TO SHIFT LEVER	SHIFT ROD
	TO SHIFT LEVER
	INDICATOR
		SHIFT
	HAIRPIN	LEVER
	CLIP	INDICATOR
	SHIFT
	ROD

FIG. 7

CHECK TIRE PRESSURE

The tires on your unit were overinﬂated at the factory for shipping purposes. Correct and equal tire pressure is important for best tilling performance.

•Reduce tire pressure to 20 PSI(1.4 kg/cm2)

HANDLE HEIGHT

•Handle height may be adjusted to better suit operator. (See “TO ADJUST HANDLE HEIGHT” in the Service and Adjustments section of this manual).

6

Image 6

Poulan 403701 INSERT CABLE CLIP See Fig, CONNECT SHIFT ROD See Fig, Remove Tiller From Crate, Check Tire Pressure

Contents

REAR TINE TILLER MODELIMPORTANT MANUAL ALWAYS WEAR EYE PROTECTION DURING OPERATIONMAINTENANCE AND STORAGE SAFETY RULESSafe Operation Practices for Walk-Behind Powered Rotary Tillers TRAININGTABLE OF CONTENTS PRODUCT SPECIFICATIONSCUSTOMER RESPONSIBILITIES CONTENTS OF HARDWARE PACK ASSEMBLYTOOLS REQUIRED FOR ASSEMBLY OPERATOR’S POSITION See FigINSTALL HANDLE See Figs. 3, 4, and UNPACKING CARTON See FigASSEMBLY REMOVE TILLER FROM CRATE INSERT CABLE CLIP See FigCONNECT SHIFT ROD See Fig CHECK TIRE PRESSUREMEETS ANSI SAFETY REQUIREMENTS OPERATIONKNOW YOUR TILLER TINE OPERATION - WITH WHEEL DRIVE HOW TO USE YOUR TILLERSTOPPING See Fig FORWARD - WHEELS ONLY/TINES STOPPEDBEFORE STARTING ENGINE OUTER SIDE SHIELDS See FigTO TRANSPORT CHECK ENGINE OIL LEVEL See FigCULTIVATING TINE SHEAR PINSTILLING HINTS OPERATIONLUBRICATION CHART MAINTENANCEMAINTENANCE SCHEDULEMAINTENANCE ENGINEAIR FILTER See Fig LUBRICATIONMUFFLER CLEANINGCOOLING SYSTEM See Fig SPARK PLUGTILLER SERVICE AND ADJUSTMENTSTO ADJUST HANDLE HEIGHT See Fig TIRE CAREGROUND DRIVE BELT ADJUSTMENT See Fig TO REPLACE GROUND DRIVE BELT See Figs. 22 andSERVICE AND ADJUSTMENTS TINE REPLACEMENT See Figs. 24, 25, and SERVICE AND ADJUSTMENTStine13 SERVICE AND ADJUSTMENTS TO ADJUST THROTTLE CONTROL CABLE See FigTO ADJUST CARBURETOR ENGINEFUEL SYSTEM STORAGEOTHER ENGINE OILTROUBLESHOOTING POINTS REPAIR PARTS HANDLE ASSEMBLYTILLER - - MODEL NUMBER PPCRT55 96091001200, PRODUCT NUMBER 960 TILLER - - MODEL NUMBER PPCRT55 96091001200, PRODUCT NUMBER MAINFRAME, LEFT SIDEREPAIR PARTS mainframeleft17MAINFRAME, RIGHT SIDE REPAIR PARTSTILLER - - MODEL NUMBER PPCRT55 96091001200, PRODUCT NUMBER TILLER - - MODEL NUMBER PPCRT55 96091001200, PRODUCT NUMBER 960 REPAIR PARTS532 18 85-54 Transmission Assembly Includes TRANSMISSIONTILLER - - MODEL NUMBER PPCRT55 96091001200, PRODUCT NUMBER TINE SHIELDREPAIR PARTS tineshield16inTILLER - - MODEL NUMBER PPCRT55 96091001200, PRODUCT NUMBER 960 91 TINE ASSEMBLYREPAIR PARTS tineipb1DECALS REPAIR PARTSTILLER - - MODEL NUMBER PPCRT55 96091001200, PRODUCT NUMBER LIMITED WARRANTY PARTS AND SERVICE