|
|
| OPERATION |
|
|
| ||
SPARK |
|
| ENGINE OIL CAP | AUGER | DRIVE | DISCHARGE | TRACTION | |
PLUG |
|
| WITH DIPSTICK | CONTROL | SPEED | CHUTE | DRIVE | |
SAFETY |
|
|
|
| LEVER | CONTROL | CONTROL | CONTROL |
IGNITION |
|
|
|
|
| LEVER | LEVER | LEVER |
KEY |
|
|
| GASOLINE |
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
| FILLER |
|
|
|
|
|
|
|
| CAP |
|
|
|
|
CHOKE |
|
|
|
| CHUTE |
|
|
|
|
|
| DEFLECTOR |
|
|
| ||
CON- |
|
|
|
|
|
| ||
TROL |
|
|
|
|
|
|
|
|
|
|
| OIL |
|
|
|
|
|
|
|
| DRAIN |
|
|
|
| |
THROTTLE |
|
| PLUG |
|
|
|
|
|
|
|
|
|
|
|
|
| |
/ ENGINE |
|
|
|
|
|
|
|
|
CONTROL |
|
|
|
|
|
|
|
|
|
|
| DISCHARGE |
|
|
|
| |
|
|
|
| CHUTE |
|
|
|
|
RECOIL | POWER |
|
|
|
|
|
|
|
(AUXILIARY) |
|
|
|
|
|
|
| |
CORD |
|
|
|
|
|
|
| |
STARTER |
|
|
|
|
|
|
| |
PLUG | ELECTRIC |
|
|
|
|
|
| |
HANDLE |
|
|
|
|
|
| ||
|
|
|
|
|
|
| ||
|
| START | FUEL |
|
|
|
| HANDLE |
|
| BUTTON | CLEAN- |
|
|
| KNOB | |
|
|
|
|
|
| |||
PRIMER |
|
| VALVE | OUT |
|
|
|
|
|
|
|
| TOOL |
|
|
|
|
|
|
|
|
|
|
|
| MUFFLER |
NOTE: ITEMS ABOVE |
|
|
|
|
|
|
| |
ARE SHOWN IN |
|
|
|
|
|
|
|
|
THEIR TYPICAL |
|
|
|
|
|
|
| TOOLBOX |
LOCATION ON THE |
|
|
|
|
|
|
| |
ENGINE. ACTUAL |
|
|
|
|
|
|
| |
LOCATION MAY VARY |
|
|
|
|
|
|
| |
WITH THE ENGINE |
|
|
|
|
|
|
| |
ON YOUR UNIT. |
|
|
|
|
|
|
|
|
SKID PLATE
AUGERS
FIG. 8
MEETS A.N.S.I. SAFETY REQUIREMENTS
Our snow throwers conform to the standards of the American National Standards Institute.
Toolbox - used to store spare shear bolts, locknuts and | Throttle/engine control - used to select either FAST or |
wrench. | SLOW engine speed and to STOP the engine. |
Safety ignition key - must be inserted for the engine to | Traction drive control lever - used to engage |
start and run. Remove when snow thrower is not in use. | pelled forward or reverse motion of snow thrower. |
Electric start button - used for starting the engine. | Auger control lever - used to engage auger motion (throw |
Recoil (auxiliary) starter handle - used for starting the | snow). |
| |
engine. | Discharge chute control lever - used to change the di- |
Primer - pumps additional fuel from the carburetor to the | rection the snow is thrown. |
| |
cylinder for use when starting a cold engine. | Skid plate - used to adjust height of scraper bar from the |
| ground. |
Choke control - used for starting a cold engine. | 8 |
|
