KEY Part Description | Poulan 420904 instruction

REPAIR PARTS SNOW THROWER - - MODEL NUMBER PR5524ES (96192001604)

AUGER HOUSING / IMPELLER ASSEMBLY

KEY	PART	DESCRIPTION
NO.	NO.	DESCRIPTION

1175321X479 IMPELLER

2196710 GEARBOX ASSEMBLY

3	188909	BEARING
4	191079	IMPELLER PULLEY
5	175322	DISCHARGE BASE

6178675X008 CORNER BRACKET

7192199 CLEAN OUT TOOL

8	405400	TOOL CLIP
9	73800400	NUT 1/4−20
10	74780426	SCREW 1/4−20 X .625
11	155377	NUT 5/16−18

12163183 SCREW 5/16−18 X .625

1319111507 WASHER

1410040500 LOCKWASHER 5/16

1574940516 SCREW 5/16−18 X 1.00

16180355 CARRIAGE BOLT

17194189 SCREW 13−16 X .625

18	407760	PLUG
19	407761	GEARBOX COVER RH
20	407766	GASKET
21	407770	SEAL
22	407762	BEARING
23	174697	THRUST WASHER 1.00
24	407763	WORM GEAR
25	407764	AUGER SHAFT
26	189282	SQUARE KEY
27	407758	BEARING
28	174683	THRUST WASHER
29	407757	IMPELLER SHAFT
30	184205	ROLL PIN
31	174681	THRUST WASHER
32	174684	THRUST BEARING
33	407769	BEARING
34	407768	O−RING

35407767 SCREW 5/16−18 X .750

36407765 GEARBOX COVER LH

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 21

Image 21

Poulan 420904 owner manual KEY Part Description

Contents

Snow Thrower Model Number Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents HOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONParts Packed Separately in Carton Remove Snow Thrower from Carton Unfold Upper Handle Install Speed Control ROD See Figs Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotater Head See FigCheck Tire Pressure Know Your Snow Thrower OperationPrimer Ignition KEY Recoil auxiliary starter handle used for starting the engine Meets A.N.S.I. Safety Requirements Stopping HOW to USE Your Snow Thrower Using the CLEAN-OUT Tool See Fig To Throw Snow See FigTo Move Forward and Backward See Fig To Start Engine Before Starting the Engine Snow Throwing Tips Before StoppingIf Recoil Starter has Frozen General Recommendations MaintenanceBefore Each USE Lubrication Engine Cleaning To Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See Fig To Replace Belts See Fig Other Storage Troubleshooting Service Notes Exploded KEY Part Description Scrapper BAR Auger HousingAuger 24 LH Auger 24 RH Bearing Plug Auger Bearing Deflector Weldment Chute WeldmentDeflector Seal Strap Rotator Head LEVER/CABLE Rotator AssemblyRotator Pivot Bracket Pulley Pivot Handle Grip Panel Bracket LH Panel Bracket RHLower Handle Pivot Support Weldment Retainer SpacerKnob RED Handle Knob Traction ROD Assembly Impeller ROD AssemblyShifter ROD TOP Shifter ROD Bottom Console Panel Wire HarnessHeadlight Bezel Flood Headlight Repair Parts Snow Thrower - Model Number PR5524ES Drive Drive Plate Assembly Speed Selector AssemblyShoulder Screw END Plate Roll PIN 3/16 Axle ShaftSprocket Clik PIN 417014X428 Engine Mount Plate KEY Part Description Engine Tecumseh Model LH195SP-67510D Belt Cover Traction BeltImpeller Belt Wheel Assembly LH Repair Parts Snow Thrower - Model Number PR5524ES Wheels Safety Ignition KEY Power CordRetainer PIN Wrench DECAL, Craftsman DECAL, DangerDECAL, DANGER, Deflector DECAL, Instruction Service Notes Service Notes Limited Warranty