Unfold Upper Handle | Poulan PR5524ESNHL, 425353 manual

ASSEMBLY / PRE-OPERATION

NOTE: The multi-wrench may be used for assembly of the chute rotator head to snow thrower and making adjustments to the skid plates.

UNFOLD UPPER HANDLE

1.Raise upper handle to the operating position and tighten handle knobs securely. Additional carriage bolts, washers and handle knobs are in bag of parts. Use to secure upper handle to lower handle. Install in lower holes in handles.

INSTALL SPEED CONTROL ROD (See Figs. 1 and 2)

1. Remove plastic tie securing rod to lower handle.

SPEED

CONTROL

ROD

PLASTIC TIE

UPPER

HANDLE

HANDLE

KNOB

LOWER

HANDLE

FIG. 1

SPEED CONTROL ROD
	RETAINER
	SPRING
SPEED	SPEED
CONTROL	CONTROL
BRACKET	LEVER

FIG. 2

2.Insert rod into speed control bracket and secure with retainer spring.install traction DRIVE control rod (See Figs. 3 and 4)

The traction drive control rod has the long loop on the end of the spring as shown.

1.Slide rubber sleeve up rod and hook end of spring into pivot bracket with loop opening down as shown.

2.With top end of rod positioned under left side of control panel, push rod down and insert top end of rod into hole in drive control bracket. Secure with retainer spring.

TRACTION DRIVE

CONTROL ROD

RUBBER

SLEEVE

LOOP OPEN-

ING DOWN

PIVOT

BRACKET

FIG. 3

TRACTION DRIVE	RETAINER
CONTROL LEVER	SPRING
	TRACTION
	DRIVE
	CONTROL
	ROD
DRIVE
CONTROL
BRACKET

FIG. 4

5

Image 5

Poulan PR5524ESNHL, 425353 owner manual Unfold Upper Handle, Install Speed Control ROD See Figs

Contents

Snow Thrower Model Number Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents HOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONParts Packed Separately in Carton Remove Snow Thrower from Carton Unfold Upper Handle Install Speed Control ROD See Figs Check Tire Pressure Install Auger Control ROD See FigsInstall Discharge Chute / Chute Rotater Head See Fig Know Your Snow Thrower OperationPrimer Ignition KEY Recoil auxiliary starter handle used for starting the engine Meets A.N.S.I. Safety Requirements Stopping HOW to USE Your Snow Thrower To Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig Before Starting the Engine To Adjust Skid Plates See FigCheck Engine OIL Level See Fig ADD Gasoline See Fig To Start Engine Snow Throwing TipsBefore Stopping If Recoil Starter has Frozen General Recommendations MaintenanceBefore Each USE Lubrication Engine Cleaning To Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See Fig To Replace Belts See Fig Other Storage Troubleshooting Service Notes Exploded KEY Part NO. NO. Description Auger Assembly LH Auger HousingAuger Assembly RH KEY Part Description Bearing Plug Auger Bearing Deflector Weldment Chute WeldmentDeflector Seal Strap Rotator Head LEVER/CABLE Rotator AssemblyRotator Pivot Bracket Pulley Pivot Handle Grip Panel Bracket LH Panel Bracket RHLower Tube Pivot Support Retainer SpacerKnob RED Handle Knob Carriage Bolt 5/16−18 X 155377 NUT 5/16−18 169675 Interlock Spring Console PanelInterlock CAM Torsion Spring Item 43 Exploded 43 402689 Drive Plate Assembly Speed Selector AssemblyEND Plate Control ARM Roll PIN 3/16 Axle ShaftSprocket Clik PIN 423184X428 Engine Mount Plate KEY Part Description Engine Tecumseh Model LH195SP-67524D Impeller Belt Belt CoverTraction Belt Wheel Assembly LH Repair Parts Snow Thrower - Model Number PR5524ESNHL Wheels Safety Ignition KEY Power CordRetainer PIN Wrench DECAL, Poulan PRO 5.5 HP/24 DECAL, DangerDECAL, DANGER, Deflector DECAL, PRO Service Notes Service Notes Limited Warranty