Loop Handle LH, Loop Handle RH, Interlock Spring

REPAIR PARTS SNOW THROWER - MODEL 961940009 (96194000901) HANDLES

	3	KEY	PART	DESCRIPTION
	3	NO.	NO.	DESCRIPTION
		1	419798X479	LOOP HANDLE LH
		2	419799X479	LOOP HANDLE RH
4	4	3	74780524	SCREW 5/16−18 X 1.50
4		4	751153	NUT 5/16−18
4
		1
3

01.08.004-B

		KEY	PART	DESCRIPTION
		NO.	NO.	DESCRIPTION
		1	412675X004	INTERLOCK SPRING
		3 2	414572	INTERLOCK CAM
	2	3	178831	TORSION SPRING
5	2	4	169675	RETAINER
5		5	17060410	SCREW 1/4−20 X .625
		5	17060410	SCREW 1/4−20 X .625
		6	421252X004	INTERLOCK STOP
	1
	6	01.08.007-B

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty.

Page 27

Image 27

Poulan 429890 Loop Handle LH, Loop Handle RH, Interlock Spring, Interlock CAM, Torsion Spring, Retainer, Interlock Stop

Contents

Snow Thrower Model Number Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Unfold Upper Handle Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from Carton Install Auger Control ROD See Figs Install Traction Drive Control ROD See Figs Install Discharge Chute / Chute Rotater Head See Fig Install Chute Deflector Remote Control See FigsCheck Tire Pressure Ignition KEY OperationKnow Your Snow Thrower Primer Recoil auxiliary starter handle used for starting engine Meets A.N.S.I. Safety Requirements Stopping HOW to USE Your Snow Thrower Using the CLEAN-OUT Tool See Fig Power Steering Operation See FigTo Move Forward and Backward See Fig Check Engine OIL Level See Fig To Adjust Skid Plates See FigBefore Starting the Engine Scraper BAR See Fig If Recoil Starter has Frozen Snow Throwing TipsTo Start Engine Before Stopping Lubrication MaintenanceGeneral Recommendations Before Each USE Cleaning Snow ThrowerEngine Shear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute Deflector To Replace Belts See Fig Engine Speed To Adjust Cable Tension See FigTo Remove Wheels See Fig Carburetor Engine OIL StorageOther Fuel System Troubleshooting KEY Part Description Auger HousingAuger Assembly 30 LH Auger Assembly 30 RH 23 22 Impeller Pulley Gearbox Assembly178675X008 Corner Bracket Clean OUT Tool Bearing Bearing Plug Auger Bearing Shield Retainer Strap Knob BlackPOP Rivet Chute Snow Shield Rotator Pivot Bracket LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Rotator Head Interlock CAM Loop Handle LHLoop Handle RH Interlock Spring Washer 3/8 SpacerKnob RED Handle Knob Shifter ROD Bottom Impeller RODTraction ROD Shifter ROD TOP Console Panel Wire HarnessLower Tube Pivot Support Sprocket Axle Shaft Exploded Rubber Ring AssemblyDrive Plate Assembly Speed Selector 427963X428 Cover AssemblyComplete LCT Engine Frame Idler Pulley Impeller BeltTraction Belt Idler ARM Bracket Clutch Slide CoverWheel Driver Retainer Ring Wheel Lobe Cable Bracket RH Cable Bracket LH 422663 Safety Ignition KEY 181037 DECAL, DangerDECAL, DANGER, Deflector HOP Limited Warranty

KEY

LOOP HANDLE LH

LOOP HANDLE RH

KEY

INTERLOCK SPRING

INTERLOCK CAM

TORSION SPRING

RETAINER

INTERLOCK STOP