Chute Weldment, Deflector Weldment, Knob Black | Poulan 96198003101

REPAIR PARTS SNOW THROWER - MODEL PP414EPS30 (96198003101)

CONTROL PANEL / DISCHARGE CHUTE

5

7

15

3

16

			*14		*11
					*11
			2		10
				6	10
			4	6
			4
KEY	PART		6		*13
					*13

NO.	NO.	DESCRIPTION
1	435023X428	CHUTE WELDMENT	1		*12
2	178633X428	DEFLECTOR WELDMENT
3	420673	DEFLECTOR CONTROL ASSEMBLY
4	420325	DEFLECTOR SEAL
5	414280	KNOB BLACK
6	128415	POP RIVET	6
7	17501010	SCREW 10-24 X .625	6
7	17501010	SCREW 10-24 X .625		9
8	430324	CHUTE SNOW SHIELD	8	9	01.09.015-B
9	419822X431	SHIELD RETAINER STRAP	8		01.09.015-B
9	419822X431	SHIELD RETAINER STRAP
*10	179829	SHOULDER BOLT 1/4-20 X .375
*11	191730	NUT 1/4-20
*12	72250505	CARRIAGE BOLT 3/8-16 X .625
*13	751153	NUT 5/16-18
*14	184505	DEFLECTOR SPRING

15420679 (SERVICE PART) DEFLECTOR CONTROL

16420672 (SERVICE PART) DEFLECTOR CABLE BLACK

NOTE:

1.ALL ITEMS INDICATED WITH AN * ARE PROVIDED IN THE BAG OF ITEMS SHIPPED LOOSE WITH PRODUCT.

2.ITEMS 15 AND 16 ARE SERVICE PART NUMBERS TO ALLOW PURCHASE OF INDIVIDUAL ITEMS IF NECESSARY.

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty.

27

Image 27

Poulan 96198003101 Chute Weldment, Deflector Weldment, Deflector Control Assembly, Deflector Seal, Knob Black, POP Rivet

Contents

Snow Thrower Model Number Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Unfold Upper Handle Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from Carton Install Auger Control ROD See Figs Install Traction Drive Control ROD See Figs Install Discharge Chute / Chute Rotator Head See Fig Install Chute Deflector Remote Control See FigsCheck Tire Pressure Ignition KEY OperationKnow Your Snow Thrower Primer Recoil auxiliary starter handle used for starting engine Meets A.N.S.I. Safety Requirements Stopping HOW to USE Your Snow Thrower To Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Adjust Skid Plates See Fig Check Engine OIL Level See Fig Before Starting the EngineScraper BAR See Fig To USE Drift Cutters See Fig If Recoil Starter has Frozen Snow Throwing TipsTo Start Engine Before Stopping Maintenance Engine Cleaning Shear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute Deflector To Replace Belts See Fig Engine Speed To Adjust Cable Tension See FigTo Remove Wheels See Fig Carburetor Engine OIL StorageOther Fuel System Troubleshooting Service Notes Exploded KEY Part Description Auger Bearing Auger HousingScrapper BAR CARRIAGEBOLT5/16−18X.625 Skid Plate RH Auger Assembly 30 LHAuger Assembly 30 RH Skid Plate LH Plastic Washer Weight BARDrift Cutter BAR CARRIAGEBOLT5/16−18X.750 Deflector Seal Deflector Control AssemblyChute Weldment Deflector Weldment Rotator Head LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Cable Assembly Heat Shield Repair Parts Snow Thrower Model PP414EPS30 Handles Pivot Support Weldment Loop Handle LHLoop Handle RH Lower Handle Washer 3/8 SpacerKnob RED Handle Knob Carriage Bolt 5/16-18 X 155377 NUT 5/16-18 169675 Repair Parts Snow Thrower Model PP414EPS30 Drive Axle ShaftSprocket Exploded Rubber Ring AssemblyDrive Plate Assembly Speed Selector Engine Mounting Plate Complete LCT EngineFrame 427963X428 Idler Pulley Impeller BeltTraction Belt Idler ARM Bracket Repair Parts Snow Thrower Model PP414EPS30 Wheels Wheel Assembly LH Cable Bracket LHCable Bracket RH Repair Parts Snow Thrower Model PP414EPS30 BAG of Parts Safety Ignition KEY422663 Repair Parts Snow Thrower Model PP414EPS30 Decals Service Notes Service Notes Limited Warranty