NOTE: If the engine sounds as if it is try- ing to start before the 5th pull, stop pulling and immediately proceed to the next step.

6.Push the choke knob in completely (to the OFF position); pull the starter rope until the engine starts.

CHOKE

(SIDE VIEW)

back toward the front handle as far as possible.

SWhen cutting with the saw, the chain brake must be disengaged.

Disengaged

Engaged

Choke knob OFF FULL

7.Allow the engine to run for approximately 5 seconds. Then, squeeze and release throttle trigger to allow engine to return to idle speed.

STARTING A WARM ENGINE:

1.Move ON/STOP switch to the ON posi- tion.

2.Push the choke knob in completely (to the OFF position).

3.Slowly press primer bulb 6 times.

4.Squeeze and hold throttle trigger. With thumb press fast idle lock down; then re- lease throttle trigger.

5.Sharply pull the starter rope with your right hand until the engine starts.

6.Squeeze and release throttle trigger to allow engine to return to idle speed.

DIFFICULT STARTING (or starting a flooded engine):

The engine may be flooded with too much fuel if it has not started after 10 pulls. Flooded engines can be cleared of excess fuel by following the warm engine starting procedure listed above. Insure the ON/ STOP switch is in the ON position.

Starting could require pulling the starter rope handle many times depending on how badly the unit is flooded. If engine fails to start, refer to the TROUBLESHOOTING TABLE or call 1-800-554-6723.

CHAIN BRAKE

WARNING: If the brake band is worn too thin it may break when the chain brake is triggered. With a broken brake band, the chain brake will not stop the chain. The chain brake should be replaced by an autho- rized service dealer if any part is worn to less than 0.020! (0.5 mm) thick. Repairs on a chain brake should be made by an autho- rized service dealer. Take your unit to the place of purchase if purchased from a ser- vicing dealer, or to the nearest authorized master service dealer.

SThis saw is equipped with a chain brake. The brake is designed to stop the chain if

kickback occurs.

S The inertia--activated chain brake is activated if the front hand guard is pushed forward, either manually (by hand) or automatically (by sudden movement).

S If the brake is already activated, it is disengaged by pulling the front hand guard

Braking function control CAUTION: The chain brake must be

checked several times daily. The engine must be running when performing this proce- dure. This is the only instance when the saw should be placed on the ground with the en- gine running.

Place the saw on firm ground. Grip the rear handle with your right hand and the front han- dle with your left hand. Apply full throttle by fully depressing the throttle trigger. Activate the chain brake by turning your left wrist against the hand guard without releasing your grip around the front handle. The chain should stop immediately.

Inertia activating function control

WARNING: When performing the following procedure, the engine must be turned off.

Grip the rear handle with your right hand and the front handle with your left hand. Hold the chain saw approximately 14! (35 cm) above a stump or other wooden surface. Release your grip on the front handle and use the weight of the saw to let the top of the guide bar fall forward and contact the stump. When the tip of the bar hits the stump, the brake should activate.

IMPORTANT POINTS

SCheck chain tension before first use and after 1 minute of operation. See CHAIN TENSION in the ASSEMBLY section.

S Cut wood only. Do not cut metal, plastics, masonry, non-wood building materials, etc.

SStop the saw if the chain strikes a foreign

object. Inspect the saw and repair or re- place parts as necessary.

SKeep the chain out of dirt and sand. Even a small amount of dirt will quickly dull a chain

and thus increase the possibility of kickback.

SPractice cutting a few small logs using the following techniques to get the “feel” of us- ing your saw before you begin a major sawing operation.

S Squeeze the throttle trigger and allow the engine to reach full speed before cutting.

S Begin cutting with the saw frame against the log.

S Keep the engine at full speed the en- tire time you are cutting.

10

Page 9 Page 11
Page 10
Image 10
Poulan 530088308 Starting a Warm Engine, Difficult Starting or starting a flooded engine, Important Points, Choke
Page 9 Page 11

530088308 specifications

The Poulan 530088308 is a high-quality replacement chain designed to deliver exceptional performance for chainsaw enthusiasts and professionals alike. This chainsaw chain is engineered for reliability and durability, ensuring users can tackle various cutting tasks with ease and efficiency.

One of the standout features of the Poulan 530088308 is its compatibility with a wide range of chainsaw models. This versatility makes it an ideal choice for those who own multiple saw brands. The chain is designed with a pitch of 3/8 inches and a gauge of .050 inches, which provides a perfect balance of cutting power and precision. The chain length typically includes 50 links, making it suitable for many chainsaws that require similar specifications.

The technology behind the Poulan 530088308 includes high-performance materials that enhance cutting speed and efficiency. The chain is crafted from high-quality steel, which not only contributes to its longevity but also helps maintain sharpness even after numerous uses. The precision-ground teeth of the chain ensure smooth and consistent cutting action, allowing users to produce clean cuts in various wood types, including hardwoods and softwoods.

Another critical characteristic of this chainsaw chain is its ease of installation and maintenance. The design facilitates quick and straightforward replacement, enabling users to get back to work in no time. Additionally, the Poulan 530088308 is engineered for optimal lubrication, which decreases wear and tear, prolonging the life of both the chain and the chainsaw itself.

The safety features incorporated into the design of the Poulan 530088308 cannot be overlooked. The chain is designed to reduce kickback, ensuring a safer cutting experience. For those who prioritize safety while operating their chainsaws, this aspect is critical in preventing accidents and injuries.

In conclusion, the Poulan 530088308 chainsaw chain stands out due to its compatibility, high-quality materials, precision engineering, and user-friendly design. Whether you are a professional woodworker or a home maintenance enthusiast, investing in this replacement chain can enhance your cutting efficiency and provide a reliable solution for your chainsaw needs.
Top Page Image Contents