ing condition of these parts. Failure to do so is a violation of the law. For normal homeowner use, the muffler and spark arresting screen will not require any service. After 50 hours of use, we recommend that your muffler be ser- viced or replaced by your Authorized Service Dealer.

CARTON CONTENTS

Check carton contents for the following:

Sbrushcutter

Stube mounting screws (2) S tube mounting nuts (2)

S handlebar screws (2) S blade shield screws (4) S cupped washer (1)

S large nut for installing blade (1) S long hex key wrench (1)

S short hex key wrench (1) S bracket cover

S shield for use with blades

S shield for use with trimmer head S semi-automatic trimmer head S shoulder strap with warning

S brush blade S handlebar

Examine parts for damage. Do not use dam- aged parts.

NOTE: If you need assistance or find that parts are missing or damaged, call 1-800-554-6723.

It is normal for the fuel filter to rattle in the empty fuel tank.

Finding fuel or oil residue on muffler is normal due to carburetor adjustments and testing done by the manufacturer.

ASSEMBLY

WARNING: Always stop unit and dis- connect spark plug before performing any as- sembly procedures.

WARNING: If received assembled, repeat all steps to ensure your unit is properly assembled and all fasteners are secure.

TOOLS REQUIRED

S2 hex key wrenches (provided)

Sadjustable wrench or large pliers S phillips screwdriver

ATTACHING THE TUBE

NOTE: Illustrations within this section will help in identifying the assembly steps. Be sure to read each section and review the illustrations, before you begin.

NOTE: A drive shaft is located in the center of the tube. Make sure this shaft does not fall out of the tube. Dirt on the shaft will significantly reduce the life of the unit. If this shaft falls out, clean, relubricate , and re-install.

SInsert the 2 tube assembly screws and nuts as illustrated. Keep loose at this time, you will tighten them during a later step.

SSome units may include a plastic cover over

the end of the tube. If your unit includes any covering, remove the cover at this time.

SPull about 1/2 inch of the drive shaft out of the inside of the tube.

Pull about 1/2 inch from tube

Tube

NOTE: The end of the drive shaft is square. This square end fits inside a square hole in a shaft inside the engine. Look inside the end of the engine and you will see the square hole in the shaft.

NOTE: The end of the tube has a groove that aligns with a ridge in the engine opening. Lo- cate the groove and ridge.

Ridge Groove

SAlign the groove in the tube with the ridge in

the engine opening. Insert the tube into the opening.

SFirmly push the tube into engine until it will no longer go into the opening.

S Tighten the screws, using one of the hex keys provided with the unit.

ATTACHING THE HANDLEBAR

DANGER: The barrier portion of the handlebar must be installed as shown to pro- vide a barrier between operator and the spin- ning blade.

SLocate the decal on the handlebar. This de- cal includes two arrows. Position the han- dlebar on the mounting bracket between

these arrows.

SPosition the bracket cover over the handle- bar. Again make sure the handlebar is be- tween the arrows.

4

Page 3 Page 5
Page 4
Image 4
Poulan 530088847 Carton Contents, Assembly Tools Required, Attaching the Tube, Attaching the Handlebar
Page 3 Page 5

530088847 specifications

The Poulan 530088847 is an effective and versatile replacement part designed to enhance the performance of your Poulan chainsaw. This component is primarily recognized as an air filter, playing a pivotal role in maintaining the engine’s efficiency and longevity. By ensuring that the air entering the combustion chamber is free from dust, debris, and contaminants, the 530088847 filter promotes optimal engine performance and fuels combustion efficiently.

One of the main features of the Poulan 530088847 is its high-quality filtration capability. The filter is built to capture even the smallest particles, preventing them from entering the engine. This is crucial because dirt and debris can cause considerable damage to the engine over time, leading to reduced performance and potential malfunctions. By using this premium air filter, chainsaw users can enjoy a longer lifespan for their equipment and maintain consistent cutting power.

Another significant characteristic of the Poulan 530088847 is its ease of installation. Designed with the user in mind, this part can be replaced quickly without the need for specialized tools or extensive mechanical knowledge. This user-friendly nature is especially beneficial for individuals who rely heavily on their chainsaws and cannot afford downtime.

Furthermore, the Poulan 530088847 is compatible with a variety of Poulan chainsaw models, making it a versatile option for many users. This compatibility ensures that individuals can find a suitable replacement for their existing air filter, further solidifying the product’s appeal within the chainsaw community.

The materials used in the construction of the Poulan 530088847 are durable and designed to withstand the rigors of outdoor usage. This resilience serves to not only extend the service life of the filter itself but also to enhance the overall reliability of the chainsaw.

Overall, the Poulan 530088847 stands out as a crucial component for maintaining the health and performance of Poulan chainsaws. Its exceptional filtration capabilities, ease of installation, compatibility, and robust construction make it an essential part for any chainsaw owner looking to optimize their equipment's performance. By investing in the 530088847 air filter, users can ensure they achieve the best possible results from their chainsaw while minimizing potential engine issues.
Top Page Image Contents