WARNING: Remove fuel cap slow- ly when refueling.

FUELING ENGINE

This engine is certified to operate on unleaded gasoline. Before operation, gasoline must be mixed with a good quality synthetic 2-cycle air-cooled engine oil designed to be mixed at a ratio of 40:1. Poulan/Weed Eater brand synthetic oil is recommended. Mix gasoline and oil at a ratio of 40:1. A 40:1 ratio is obtained by mixing 3.2 ounces (95 ml) of oil with 1 gallon (4 liters) of unleaded gasoline. Included with this saw is a 3.2 ounce container of oil. Pour the entire contents of this container into 1 gallon of gasoline to achieve the proper fuel mixture. DO NOT USE automotive oil or boat oil. These oils will cause engine damage. When mixing fuel, follow instructions printed on container. Once oil is added to gasoline, shake container momentarily to assure that the fuel is thoroughly mixed. Always read and follow the safety rules relating to fuel before fueling your unit.

BAR AND CHAIN LUBRICATION

The bar and chain require continuous lubri- cation. Lubrication is provided by the auto- matic oiler system when the oil tank is kept filled. Lack of oil will quickly ruin the bar and chain. Too little oil will cause overheating shown by smoke coming from the chain and/ or discoloration of the bar.

In freezing weather oil will thicken, making it necessary to thin bar and chain oil with a small amount (5 to 10%) of #1 Diesel Fuel or kerosene. Bar and chain oil must be free flowing for the oil system to pump enough oil for adequate lubrication.

Genuine Poulan or Poulan PROR bar and chain oil is recommended to protect your unit against excessive wear from heat and friction. Poulan or Poulan PROR oil resists high temperature thinning. If Poulan or Poulan PROR bar and chain oil is not available, use a good grade SAE 30 oil.

SNever use waste oil for bar and chain lubri-

cation.

S Always stop the engine before removing the oil cap.

IMPORTANT

Experience indicates that alcohol--blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage for 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. See STORAGE section for addi- tional information.

9

WARNING: The chain must not move when the engine runs at idle speed. If the chain moves at idle speed refer to CAR- BURETOR ADJUSTMENT within this manual. Avoid contact with the muffler. A hot muffler can cause serious burns.

To stop the engine move the ON/STOP switch to the STOP position.

To start the engine hold the saw firmly on the ground as illustrated. Make sure the chain is free to turn without contacting any object.

Use only 15”---18” of rope per pull. Hold saw firmly while pulling starter rope

Starter rope handle

Left hand

on front handle

Right foot through rear handle

IMPORTANT POINTS TO REMEMBER

When pulling the starter rope, do not use the full extent of the rope as this can cause the rope to break. Do not let starter rope snap back. Hold the handle and let the rope rewind slowly.

For cold weather starting, start the unit at FULL CHOKE; allow the engine to warm up before squeezing the throttle trigger.

NOTE: Do not cut material with the choke/ fast idle lever at the FULL CHOKE position.

STARTING A COLD ENGINE (or warm engine after running out of fuel):

NOTE: In the following steps, when the choke/fast idle lever is pulled out to the full extent, the correct throttle setting for starting is set automatically.

1.Move ON/STOP switch to the ON posi- tion.

2.Pull out choke/fast idle to the full extent.

3.Slowly press primer bulb 6 times.

4.Pull the starter rope quickly with your right hand 5 times. Then, proceed to the next step.

NOTE: If the engine sounds as if it is trying to start before the 5th pull, stop pulling and immediately proceed to the next step.

5.Push the choke/fast idle lever in com- pletely (to the OFF position).

6.Pull the starter rope quickly with your right hand until the engine starts.

7.Allow the engine to run for approximately 5 seconds. Then, squeeze and release throttle trigger to allow engine to return to idle speed.

Page 8 Page 10
Page 9
Image 9
Poulan 530163652 Fueling Engine, BAR and Chain Lubrication, Important Points to Remember, Right foot through rear handle
Page 8 Page 10

530163652 specifications

The Poulan 530163652 is a high-performance chainsaw that has gained significant popularity among both amateur and professional users. Its robust design and advanced features make it an ideal tool for various cutting tasks, whether for pruning trees, chopping firewood, or tackling larger forestry jobs.

One of the standout features of the Poulan 530163652 is its powerful engine. Equipped with a reliable 2-cycle engine, this chainsaw delivers high performance while maintaining fuel efficiency. This balance ensures that users can complete their tasks without frequent refueling, making it a convenient choice for extended projects.

Another prominent characteristic of the Poulan 530163652 is its lightweight construction. Weighing in at manageable levels, this chainsaw is designed for ease of use, reducing fatigue during extended operation. The lightweight nature, combined with an ergonomic handle, allows for comfortable maneuverability, making it suitable for both novice and experienced operators.

The chainsaw features an automatic oiling system, which ensures a constant supply of lubrication to the chain and bar. This technology reduces friction, enhances cutting performance, and prolongs the life of the chainsaw. With an easy access chain tensioning system, users can quickly adjust the tension without the need for additional tools, saving time and enhancing user convenience.

Safety is paramount in any chainsaw, and the Poulan 530163652 includes essential safety features such as a chain brake that can be activated in the event of kickback. The protective handguard also adds an extra layer of safety, shielding the operator’s hands from debris and accidental contact with the chain.

In terms of maintenance, the Poulan 530163652 is designed for simplicity. The accessible air filter and spark plug make routine maintenance tasks straightforward, allowing users to keep their chainsaw in optimal working condition with minimal hassle.

In summary, the Poulan 530163652 is a well-rounded chainsaw that combines power, efficiency, and safety features. Its lightweight design, automatic oiling system, easy chain adjustment, and user-friendly maintenance make it a top choice for those looking to tackle cutting tasks effectively and safely. Whether for home use or professional applications, this chainsaw stands out as a reliable tool that delivers consistent results.
Top Page Image Contents