To Remove Wheel See Fig | Poulan 532 43 88-78, 96048000500 specification

SERVICE AND ADJUSTMENTS

TRANSAXLE MOTION CONTROL LEVER NEUTRAL ADJUSTMENT (See Fig. 33)

The motion control lever has been preset at the factory and adjustment should not be necessary.

•Loosen adjustment bolt in front of the right rear wheel, and lightly tighten.

•Start engine and move motion control lever until tractor does not move forward or backward.

•Hold motion control lever in that position and turn engine off.

•While holding motion control lever in place, loosen the adjustment bolt.

•Move motion control lever to the neutral (lock gate) position.

•Tighten adjustment bolt securely.

NOTE: If additional clearance is needed to get to adjustment bolt, move mower deck height to the lowest position.

After above adjustment is made, if the tractor still creeps forward or backward while motion control lever is in neutral position, follow these steps:

•Loosen the adjustment bolt.

•Move the motion control lever 1/4 to 1/2" in the direc- tion it is trying to creep.

•Tighten adjustment bolt securely.

•Start engine and test.

•If tractor still creeps, repeat above steps until satisfied.

MOTION CONTROL	NEUTRAL
LEVER	LOCK
	GATE
	ADJUSTMENT
	BOLT

Fig. 33

TO REMOVE WHEEL (See Fig. 34)

•Block up axle securely.

•Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).

•Repair tire and reassemble.

•On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

RETAINING WASHERS

RING

AXLE

COVER

SQUARE KEY

(REAR WHEEL ONLY)

Fig. 34

•Replace washers and snap retaining ring securely in axle groove.

•Replace axle cover.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not adjustable on your tractor. If damage has occurred to affect the front wheel toe-in or camber, contact your nearest authorized service center/department.

TO START ENGINE WITH A WEAK BATTERY (See Fig. 35)

WARNING: Lead-acid batteries gen- erate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the Maintenance section of this manual).

If “jumper cables” are used for emergency starting, follow this procedure:

IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES.

TO ATTACH JUMPER CABLES -

•Connect one end of the RED cable to the POSITIVE

(+)terminal of each battery(A-B), taking care not to short against tractor chassis.

•Connect one end of the BLACK cable to the NEGATIVE (-) terminal (C) of fully charged battery.

•Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER -

•BLACK cable first from chassis and then from the fully charged battery.

•RED cable last from both batteries.

WEAK OR

FULLY CHARGED

DEAD BATTERY

BATTERY

Fig. 35

96048000500, 532 43 88-78 specifications

The Poulan 532 43 88-78,96048000500 is an innovative lawn mower accessory designed to enhance lawn maintenance efficiency. Known for its robust build quality and reliability, this piece of equipment is favored by both homeowners and professional landscapers.

One of the standout features of the Poulan 532 43 88-78,96048000500 is its compatibility with a variety of Poulan lawn mowers. This ensures that users can easily integrate this accessory into their existing lawn care systems. The design focuses on versatility, allowing it to work seamlessly with different models, making it a versatile addition to any green space toolkit.

Equipped with a powerful engine, the Poulan 532 features advanced technologies that optimize performance. The cutting system is designed with precision blades that deliver clean and even cuts. This not only enhances the appearance of the lawn but also promotes healthier grass growth by reducing stress on the plants.

Durability is a key characteristic of this product. Constructed from high-grade materials, the Poulan 532 is built to withstand the rigors of regular use. Its rugged design minimizes wear and tear, ensuring longevity and reliability, even in challenging conditions.

This model also incorporates easy-start technology, which allows users to start the machine with minimal effort. This feature is particularly useful for those who may struggle with traditional pull-start mechanisms. Furthermore, the user-friendly controls make operation straightforward, appealing to both novices and experienced users alike.

In addition, the Poulan 532 43 88-78,96048000500 offers adjustable cutting height settings, allowing users to customize the length of grass cut to their preference. This feature grants lawn caretakers the flexibility to maintain their lawns according to seasonal needs or individual aesthetic choices.

Maintenance is made easy with the Poulan 532, thanks to its accessible design. Routine checks and part replacements can be conducted without significant hassle, promoting a longer lifespan for the machine. Users appreciate that they can spend less time on upkeep and more time enjoying their beautifully manicured lawns.

Overall, the Poulan 532 43 88-78,96048000500 stands out in the market for its combination of powerful performance, user-friendly features, and durable construction. Perfect for anyone who values quality lawn equipment, this accessory is sure to meet the demands of modern lawn care while providing exceptional results.

Poulan 532 43 88-78, 96048000500 manual Transaxle Motion Control Lever Neutral Adjustment See Fig

Models: 96048000500 532 43 88-78