HOW to Start Your Unit, Starting a Cold Engine

ON/OFF Switch

HOW TO START YOUR UNIT

WARNING: Avoid any contact with the muffler. A hot muffler can cause serious burns.

Starting Position

HELPFUL TIP

If your engine still does not start after following these instructions, please call 1-800-554-6723.

STARTING A COLD ENGINE

NOTE: DO NOT squeeze the throttle trigger until the engine has started and runs.

1.Set unit on a flat surface.

2.Move ON/OFF switch to the ON position.

3.Slowly press the primer bulb 6 times.

4.Move the start lever to the START posi- tion.

Starter Handle

Start

Lever

Primer Bulb

Muffler

5.Pull starter rope handle sharply until en- gine starts and runs.

6.Allow unit to run for 5 seconds, then fully squeeze the throttle trigger to disengage the starting system.

STARTING A WARM ENGINE

1.Move ON/OFF switch to the ON position.

2.Squeeze and hold the throttle trigger. Keep throttle trigger fully squeezed until engine runs smoothly.

3.Pull starter rope sharply while squeezing throttle trigger until engine runs.

NOTE: Normally, the warm starting proce- dure can be used within 5--10 minutes after the unit is turned OFF. If the unit sits for more than 10 minutes without being ran, it will be necessary to start the unit by following the steps under STARTING A COLD ENGINE or following the starting instruction steps shown on the unit.

STARTING A FLOODED ENGINE

Flooded engines can be started by placing the ON/OFF switch in the ON position. Move the start lever to the RUN position and fully squeeze throttle trigger. Pull the starter han- dle repeatedly while squeezing throttle trigger until engine starts and runs. This could re- quire pulling the starter handle many times, depending on how badly the unit is flooded. If the unit still doesn’t start, refer to TROUBLESHOOTING TABLE or call 1-800-554-6723.

OPERATING THE COUPLER

This model is equipped with a coupler which enables optional attachments to be installed. The optional attachments are:

MODEL: Edger . . . . . . . . . . . . . . . . . . . . . PP1000E Cultivator . . . . . . . . . . . . . . . . . . PP2000T Blower . . . . . . . . . . . . . . . . . . . . PP3000B Brushcutter . . . . . . . . . . . . . . . . PP4000C Pruner . . . . . . . . . . . . . . . . . . . . PP5000P

WARNING: Always stop unit and dis- connect spark plug before removing or instal- ling attachments.

REMOVING TRIMMER ATTACH- MENT (OR OTHER OPTIONAL ATTACHMENTS)

CAUTION: When removing or installing at- tachments, place the unit on a flat surface for stability.

1.Loosen the coupler by turning the knob counterclockwise.

	Upper
Coupler	Shaft
Lower	LOOSEN
Lower
Attachment
TIGHTEN	Knob

2.Press and hold the locking/release button. Locking/Release

Button

	Coupler	Upper Shaft
	Lower Attachment	Upper Shaft
	Lower Attachment

3.While securely holding the engine and upper shaft, pull the attachment straight out of the coupler.

INSTALLING OPTIONAL ATTACH- MENTS

1.Remove the shaft cap from the attach- ment (if present).

2.Position locking/release button of attach- ment into guide recess of coupler.

3.Push the attachment into the coupler until the locking/release button snaps into the primary hole.

4.Before using the unit, tighten the knob se- curely by turning clockwise.

545137291 specifications

The Poulan 545137291 is a versatile and powerful chainsaw designed for homeowners and professionals alike. Renowned for its reliability and performance, this tool is an essential asset for anyone looking to tackle various cutting tasks, from felling trees to limbing branches and cutting firewood.

One of the standout features of the Poulan 545137291 is its robust engine. Powered by a 50cc, 2-cycle engine, this chainsaw delivers impressive cutting speed and efficiency. The high engine power ensures that users can effectively handle even the toughest jobs with ease. Furthermore, the engine is designed to optimize fuel efficiency, allowing users to get more work done on a single tank of gas while minimizing emissions, adhering to modern environmental standards.

The chainsaw is equipped with a 20-inch bar and chain, providing ample length for cutting through larger logs and trees. The combination of the powerful engine and the extended bar ensures that it can cut through hardwoods and softwoods alike with minimal effort. The chain itself features a low kickback design, enhancing safety during use and allowing for more control while operating.

Another noteworthy feature of the Poulan 545137291 is its user-friendly design. The chainsaw comes equipped with an easy-starting system, often featuring a simplified starting procedure that reduces the manual effort typically required to start a 2-cycle engine. Additionally, it has an ergonomic handle with a comfortable grip, which reduces user fatigue during extended use. This is especially important for users who may be working for long hours.

Maintenance is made manageable with the Poulan 545137291. It features a tool-less chain tensioning system, allowing users to easily adjust the chain tension without the need for any additional tools. This ensures the chain remains in optimal condition for safe and efficient cutting. Moreover, the air filter is easily accessible for routine cleaning and replacement, promoting better engine performance over time.

In summary, the Poulan 545137291 chainsaw is designed with a blend of power, safety, and user convenience. With its 50cc engine, 20-inch bar, low kickback chain, and user-friendly features, it stands out as a reliable choice for both novice and experienced users alike. Whether for regular yard maintenance, storm cleanup, or larger forestry projects, this chainsaw provides the performance and functionality needed to get the job done effectively.

Poulan 545137291 HOW to Start Your Unit, Starting a Cold Engine, Starting a Warm Engine

Models: 545137291